daisalux TEV-500 Buku Petunjuk - Halaman 2

Jelajahi secara online atau unduh pdf Buku Petunjuk untuk Pengontrol daisalux TEV-500. daisalux TEV-500 10 halaman.

Halaman Cetak

OPERATION:

The Daisalux Central TEV:

- Manages the communication among the control computer and the

devices of DaisaTest system. The communication with the control

computer can be with an RS232 connection or ETHERNET.

- Detecs and informs if there are failures in the Principal bus (shortcircuit

and leakages) by means of the pilots.

- Manages the duration tests and functional tests that the self-contained

luminaires have to do, even when the PC is switched off or disconnected.

- It has an AUX input to command an alert (see options in DaisaTest).

That is activated by a potential free contact when switching to open

circuit. It is useful to be connecte to a fire panel.

- It can work as a remote control: standby mode and re-switch on.

- Connecting th battery module MBAT 12-11, it keeps its operation with

no mains on (more than 1 hour duration).

- It has a TEST-BUS button to make easier the starting up and checkinf

of the bus.

There are 3 models:

- Central TEV-200: admits 200 devices maximum connected to the Bus.

- Central TEV-500: admits 500 devices maximum connected to the Bus.

- Central TEV-1000: admits 1000 devices maximum connected to the

Bus.

PUSH BUTTONS:

: it switches on again all the devices with a battery that are in

standby mode (including the Central TEV). This re-switch on takes

between 8 and 15 seconds.

: it takes to standby mode all the devices that have no mains supply

(including the Central TEV).

TESTBUS: it takes the unit to TEST-BUS Mode, which causes the

intermittence of the signalling pilots of the TCA luminaires that are

correctly connected to the Bus, allowing this way to check that the

bus wiring is OK. To exit this TEST-BUS Mode press TESTBUS

button again or wait 12h, after which the unit returns to normal

operation mode.

INDICATION PILOTS:

: Pilot ON indicates that the unit has mains supply (L, N).

: Pilot ON indicates that the MBAT 12-11 module is correctly

connected.

BUS: Pilot ON indicates that the Principal Bus is OK.

Intermittent pilot indicates that the unit is in TEST-BUS Mode.

: Pilot OFF: the unit does not communicate with SoftDaisatest

program in the PC.

Intermittent pilot: it is necessary to connect the unit to the PC to

check if the maintenance of the installation must be performed.

Pilot ON: the unit communicates with SoftDaisatest program in

the PC and all the data of the installation are transmitted.

SHORTCIRCUIT: indicates that there is a shortcircuit in

the Principal Bus wiring.

LEAKAGES: indicates that one or both wires of the

Principal Bus is in contact with the mains supply L, N.

CONNECTIONS:

- L, N: 220-230V~ 50/60 Hz, or 110-127V~ 50/60Hz.

- BUS: Connection to Principal Bus (BUS P) of Daisatest installation (see

Wiring Guide).

- AUX: Input for potential-free contact.

- MBAT 12-11: Connection to MBAT 12-11 module (accesory).

- RS-232: Connection to PC via serial port.

ETHERNET: Connection to PC via local network (auto-sensing

10/100Base-T).

TECHNICAL CHARACTERISTICS:

- MAINS SUPPLY L, N: Marked on the appliance

- CONSUMPTION CURRENT: Marked on the appliance

- DIMENSIONS: 141 x 83 x 54 mm (equivalent to 8 standard

magnetothermal switches)

- Connection to control computer OPTOAISOLATED from Principal Bus.

- WEIGHT: 540gr

- DURATION: 1h with MBAT 12-11 battery module (accessory).

ASSEMBLY INSTRUCTIONS:

Fix the Central TEV in a DIN 46277/3 rail. It must be installed in the

interior of an electric board.

For the Bus connections, Daisalux ref:BUS-TAM wire must be used.

WIRING OF A DAISATEST INSTALLATION:

Together with the Central TEV a RS232 cable, an Ethernet cable and a

pendrive with the software for the start up of the installation are

supplied.

Follow the WIRING GUIDE attached to this instructions leaflet and

request start up of the installation from Daisalux, where how to use the

received items will be showed.

MAINTENANCE AND CAUTION:

- Before connection of the unit always check that the voltage of the

distributing mains supply corresponds with that specified on the unit.

- Any installation or maintenance procedure must be carried out by

qualified personnel. Make sure the unit is disconnected from the MAINS

before performing any maintenance procedure.

- Keep these instructions.

[CENTRALTEV]