Foxconn R10-S2 Spesifikasi

Jelajahi secara online atau unduh pdf Spesifikasi untuk Desktop Foxconn R10-S2. Foxconn R10-S2 2 halaman. Small form factor barebone chassis quick installation

Halaman Cetak

Small Form Factor Barebone

Chassis Quick Installation

SFF R10-S2

SPECIFICATION

M/B Configuration

Mini ITX MB

Dimension (W/H/D)

283*282*95 (mm)

1*5.25" External

Drive Bays

1*3.5" External

1*3.5" Internal

2*USB2.0

Front I/O Ports

1* Micphone,

1*Earphone

SPS

TFX 150W

Fan

80*80*20mm

WEEE:

The use of this symbol indicates that this product may not be treated as household waste. By ensuring this product

is disposed of correctly, you will help prevent potential negative consequences for the environment and human

health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed

information about recycling of this product, please contact your local city office, your household waste disposal

service or the shop where you purchased this product.

All image are for reference only, please refer to the physical chassis for specific features.

P/N: 3A250J000-000-G

Bezel View

USB Port

Line Out

USB接口

音频输出端口

Microphone In

USB

音源輸出

埠

音频输入端口

USBポット

ラインアウト

音源輸入

USB포트

라인 출력

マイク入力

마이크 입력

USB-Anschluss

Line-Ausgang

linea de Salida

Puerto de USB

Mikrofon-Eingang

Port USB

Sortie ligne

Entrada de micrófono

HatÇıkışı

USB Bağlantı Noktası

Entrée microphone

Porta USB

Uscita linea

Mikrofon Girişi

Porta USB

Saída de linha

Линейный выход

Ingresso microfono

Порт USB

Entrada microfone

Port USB

wyjście liniowe

Vonalszintű kimenet

Вход микрофона

USB csatlakozó

wejście mikrofonu

Mikrofon bemenet

Optical Disk Drive

Reset Button

光驱

重启按钮

光碟機

Power Button

光学ディスクドライブ

重啟開關

电源开关

リセットボタン

옵티컬 디스크 드라이브

電源開關

재설정 버튼

パワーボタン

Optisches Laufwerk

전원 버튼

Reset-Taste

Unidad de disco Optico

Botón de reinicio

l'unité de disques optique

Power-Taste

Bouton de remise

Mikrofon Girişi Optik Disk Sürücü

Botón de encendido

Sıfırlama Düğmesi

unità disco ottico

Bouton de puissance

Tasto Reset(Ripristino)

Güç Düğmesi

Drive do disco óptico

Botão Reiniciar

Оптический привод

Tasto Power

Кнопка Reset

stacja dysków optycznych

Botão Alimentação

przycisk resetowania

Optikai lemezmeghajtó

Кнопка питания

Alaphelyzet gomb

przycisk zasilania

Üzemkapcsoló gomb

Rear Panel View

Rear I/O

后面板接口

後面板

リアI/O

후면 I/O

Rückwärtige I/O

I/O trasero

Rear I/O

Arka G/Ç

I/O posteriore

E/S de trás

Вход/выход задней панели

tylne wejście/wyjście (I/O)

Hátsó I/O csatlakozók

Power Cord Input

电源接口

電源輸入

電源コード入力

전원 코드 입력

Stromkabel Eingang

Cable de alimentación de entrada

Cordon d'alimentation d'entrée

Güç Kablosu Girişi

ingresso cavo d'alimentazione

Entrada do cabo de alimentação

Вход штура питания

wejście kabla zasilającego

Tápkábel bemenet

Open the case

1. Take the chassis out of its packing.

2. Remove the top cover screw on the

real panel.

Top cover (or Side Panel)

Front

Panel

Remove Bezel and Driver Bay

1. Release four clips on the bezel top.

2. Hold the bezel with both hands, lift

left hand side to release two bottom

clips.

5. Push driver bay toward real panel and lift it

to remove.

Install Memory

1. Spread the clips at both ends of the

2. Memory module has asymmetric pin

memory socket.

counts in its two sides separated by a

notch in the middle, so it can only fit in

one direction.

Install Hard Disk Drive (HDD)

1. Put the HDD into the chassis as depicted

2. Move the HDD to align with three

in the picture.

screw holes.

4. Use provided shorter SATA cable to

5. Connect power cable to HDD.

connect motherboard and HDD.

3. Remove the top cover by pushing it toward

4. Check there are motherboard, power

real panel, and lift it.

supply and driver bay inside.

Top cover

3. Lift right hand side to release another

4. Remove two screws to detach

bottom clip.

the driver bay.

6. Now, you can start the installations of

memory, hard drive and optical disk drive.

3. Place the memory module onto the

4. The clips at both ends of the socket will

socket, then push it down firmly and

snap into place when the memory module

seat it vertically into the memory

is securely inserted.

socket.

3. Fasten the HDD with three screws.