DSC PC2525 Buku Petunjuk - Halaman 6

Jelajahi secara online atau unduh pdf Buku Petunjuk untuk Sistem Keamanan DSC PC2525. DSC PC2525 17 halaman. Dsc pc2525 security system instruction manual
Juga untuk DSC PC2525: Buku Petunjuk (13 halaman), Buku Petunjuk (16 halaman), Buku Petunjuk (13 halaman)

Halaman Cetak

To Bypass Zones:

Enter [ ][1]; the "Bypass" light will FLASH.

Enter the number of the zone to be bypassed; the corresponding Zone Light will come ON to indicate that

the zone is bypassed. To remove a bypass, enter the zone number to shut its Zone Light OFF. When all

desired zones are bypassed, press the [#] Key to return to "Ready". Notice that the "Bypass" light will be

ON while the system is disarmed to indicate that zones have been bypassed.

When you arm your system, the zones you have indicated will now be bypassed. Before arming the

system with bypassed zones, it is always a good idea to enter the [ ][1][Access Code] command to

review the list of bypassed zones before entering an Access Code to arm the system. After ensuring that

the desired zones are bypassed, press the [#] Key, and then enter an Access Code to arm the system.

When the system is disarmed, the zone bypasses will be cleared and the zone will again be active.

To Recall Bypassed Zones:

Enter [ ][1][9]; the "Bypass" light will FLASH and Zone Lights will come ON to indicate which zones were last

bypassed. This feature is useful if you bypass the same set of zones regularly; by recalling the set of bypassed

zones, you won't have to enter the zone numbers for each zone each time you wish to bypass the same set.

Access Code Required for Bypass:

Your security system may be programmed to require an Access Code to be entered to bypass zones. Your

installer will inform you if this option has been enabled on your system.

If an Access Code is required for bypassing, enter [ ][1][Access Code], and follow the bypassing

instructions described above.

Keypad Alarms

Three types of alarms may be activated by pressing and holding a single key on the keypad. Your

installer will inform you of how the [F], [A] and [P] Keys will operate on your system.

[F]ire

Press and hold the [F] Key for 2 seconds to sound a Fire alarm; the siren will sound with a pulsed

tone. The keypad will sound a series of short beeps once the system has accepted the alarm.

If enabled by your installer, a transmission will be sent to your monitoring station.

[A]uxiliary Press and hold the [A] Key for 2 seconds to generate an Auxiliary alarm. The siren will not sound

when this function is activated. The keypad will sound a series of short beeps once the system

has accepted the alarm. If enabled by your installer, a transmission will be sent to your

monitoring station.

[P]anic

Press and hold the [P] Key for 2 seconds to generate a Panic alarm. The alarm may be

programmed as either silent or audible; your installer will inform you of how this alarm will

operate. If your installer has programmed this alarm to be audible, the keypad will sound a

series of short beeps once the system has accepted the alarm, and the siren will sound a steady

tone. If enabled by your installer, a transmission will be sent to your monitoring station.

Utility Output Command

A special keypad command may be used to operate various devices connected to your security system. To

operate the Utility Output, enter [ ][7] on the keypad. An Access Code may also need to be entered to use

this command; your Installer will inform you if an Access Code is required to activate the Utility Output.

When the command is entered, the keypad will sound a single tone for 5 seconds, and the Utility Output

will be activated for 5 seconds.

This command may be used to operate devices such as special lighting or door strikes. This feature

may also be used to reset smoke detectors that are connected to your system. Refer to the "Fire Zone

Operation" section of this manual for information.

Your installer will inform you of how the Utility Output function is set up for your system.