FOXEER DigiSight Nano Panduan Memulai Cepat
Jelajahi secara online atau unduh pdf Panduan Memulai Cepat untuk Kamera Digital FOXEER DigiSight Nano. FOXEER DigiSight Nano 2 halaman.
Halaman Cetak
DigiSight Nano
WARNING:
Read the ENTIRE instruction
manual to become familiar with the
features of the product before operating.
Failure to operate the product correctly
can result in damage to the product,
personal property and cause serious
injury.
NOTICE: This product is only intended for
use with unmanned, hobby- grade,
remote-controlled vehicles and aircraft.
FOXEER disclaims all liability outside of
the intended purpose and will not
provide warranty service related thereto.
SUPPORT: Visit www.foxeer.com/ to get
more information.
CAMERA-OSD SWITCH
CONNECTION
If you connected with HD VTx, you need to
change cam setting from VTx side.
(via programming board)
OSD Switch Front
Camera
Back
VCC
Analog: 4.5V~20V
Digital: 3.3V(Red)
GND
Ground Wire(Black)
Digital VTX
VID
Video Out(Yellow)
OSD
OSD(White)
CAUTION: If you are using ESC's with active
braking, we recommend powering the
camera system through a BEC or voltage
regulator.
CAMERA-VIDEO
TRANSMITTER CONNECTION
Analog: To connect the camera directly to the
video transmitter, plug the 3 pin wiring harness
from the video transmitter into the camera
leaving the OSD pin open.
Digital: plug the ribbon cable from the camera
to the video transmitter.
Switch Between Analog
And Digital
The analog and digital can not be used
simultaneously, default is digital, if you want to
switch to digital, Power on for 20 seconds,
long press the left button for 5 seconds.
FPV OSD Setup
Press top button for 3s, you can access OSD
menu.
DISPLAY
TIME
SCENE
SIZE
SYSTEM
VER: FOXEER_HD_V1.0
EXIT
1. TIME: ON/OFF
2. SCENE: DAY/ NIGHT/ LED/ B&W.
Quick switch:
At standby status, long press the right
button on OSD board, it can fast change the SCENE,
the current mode will show once at the TIMER place.
3. SIZE: 4:3/16:9 switchable.
4. SYSTEM: 60/50FPS switchable.
5. VER: FOXEER_HD_V1.0.
Main MENU
SETUP MENU
CAMERA ID
PICT ADJUST
DAY / NIGHT
LANGUAGE
CAMERA RESET
EXIT
MENU: Push MENU(center button) to go to
the main menu.
UP/DOWN: Move up and down through the
menu.
Left/Right: Modify the menu parameters.
1. Camera ID
Camera ID: ON/OFF. You can setup pilot
name and position.
FOXEER
RETURN
2. PICT ADJUST
PICT ADJUST
RETURN
1. FLIP: OFF/ H-FLIP/ V-FLIP/ HV-FLIP
2. BRIGHTNESS
3. CONTRAST
4. SHARPNESS
5. HUE
ON
DAY
6. COLOR GAIN
4:3
60FPS
3. DAY/NIGHT
DAY/NIGHT include "AUTO" and "MANUAL" ,
click "MANUAL" , you can setup permanent
"COLOR" or "B/W" .
4. LANGUAGE
7 Languages: ENGLISH/ DEUTSCH/ FRANCAIS/
PYCCKNN/ PORTUGUES/ ESPANOL/ 中文 .
ON
5. Camera reset
AUTO
ENGLISH
6. EXIT
YES
Save All: Save all setup.
Not Save: Can save the value temporary, but
once power o , the value won't save.
cancel: Cancel Setup.
CAMERA ID
00 : 00
00 : 0
A B C D E F G H I J K L M N O P Q
R S T U V W X Y Z
- ! " # $ % & ( ) _ ˋ , ￥ : ; <=> ? @
\ ˆ﹡﹣×＋／
←→↑↓ CLR POS
FLIP
OFF
BRIGHTNESS
122
CONTRAST
136
SHARPNESS
160
HUE
090
COLOR GAIN
136
DAY/NIGHT
DAY/NIGHT
COLOR
RETURN