DSC BRAVO5 Petunjuk Instalasi - Halaman 2

Jelajahi secara online atau unduh pdf Petunjuk Instalasi untuk Sensor Keamanan DSC BRAVO5. DSC BRAVO5 2 halaman. Ceiling mount pir detector

Halaman Cetak

Wiring

Refer to the following diagram for wiring instructions:

Power Up

Upon application of power, the LED will be on for

approximately 90 seconds to indicate that the unit is warming

up. During this period, the relay is held in its alarm state. After

the 90 second warm-up period, the LED will turn off and the

unit will respond to motion in the protected area.

Testing

IMPORTANT NOTE: Upon installation, test the unit

thoroughly tested to ensure it works properly. The end user

should be instructed on how to perform walk tests, and

should perform a walk test of the detector weekly.

Walk Test

Create movement in the entire area where coverage is

needed.

The LED on the unit will turn on whenever motion is detected

(jumper J1 must be on).

If coverage is incomplete, relocate the unit. You can make

minor adjustments by rotating the detector several degrees.

Refer to the coverage pattern diagrams as a guide to

reposition the detector for better coverage.

Once the detector coverage is as required, you may turn off

the alarm LED by removing the jumper from J1.

Changing the Sensitivity

Bravo5 features Fast and Slow detection modes, which are

set on jumper J2. Jumper J2 is set at the factory for the Fast

detection mode. In a normal operating environment, this

setting provides the best detection.

In certain environments where rapid air movement, heaters

and other variables present problems, use Slow detection

mode to stabilize the detection.

To change the setting from Fast to Slow, take the jumper off

the header.

Limited Warranty

Digital Security Controls Ltd. warrants that for a period of five years

from the date of purchase, the product shall be free of defects in

materials and workmanship under normal use and that in fulfilment

of any breach of such warranty, Digital Security Controls Ltd. shall,

at its option, repair or replace the defective equipment upon return

of the equipment to its repair depot. This warranty applies only to

defects in parts and workmanship and not to damage incurred in

shipping or handling, or damage due to causes beyond the control of

Digital Security Controls Ltd. such as lightning, excessive voltage,

mechanical shock, water damage, or damage arising out of abuse,

alteration or improper application of the equipment.

The foregoing warranty shall apply only to the original buyer, and is

and shall be in lieu of any and all other warranties, whether expressed

or implied and of all other obligations or liabilities on the part of

Digital Security Controls Ltd. Digital Security Controls Ltd. neither

assumes, nor authorizes any other person purporting to act on its

behalf to modify or to change this warranty, nor to assume for it any

other warranty or liability concerning this product.

In no event shall Digital Security Controls Ltd. be liable for any direct,

indirect or consequential damages, loss of anticipated profits, loss of

time or any other losses incurred by the buyer in connection with the

purchase, installation or operation or failure of this product.

Motion detectors can only detect motion within the designated ar-

eas as shown in their respective installation instructions. They can-

not discriminate between intruders and intended occupants. Motion

detectors do not provide volumetric area protection. They have

multiple beams of detection and motion can only be detected in

unobstructed areas covered by these beams. They cannot detect

motion which occurs behind walls, ceilings, floor, closed doors, glass

partitions, glass doors or windows. Any type of tampering whether

intentional or unintentional such as masking, painting, or spraying

of any material on the lenses, mirrors, windows or any other part of

the detection system will impair its proper operation.

Passive infrared motion detectors operate by sensing changes in tem-

perature. However their effectiveness can be reduced when the ambi-

ent temperature rises near or above body temperature or if there are

intentional or unintentional sources of heat in or near the detection

area. Some of these heat sources could be heaters, radiators, stoves,

barbeques, fireplaces, sunlight, steam vents, lighting and so on.

Warning: Digital Security Controls Ltd. recommends that the entire

system be completely tested on a regular basis. However, despite frequent

testing, and due to, but not limited to, criminal tampering or electrical

disruption, it is possible for this product to fail to perform as expected.

Important Information: Changes or modifications not expressly approved

by Digital Security Controls Ltd. could void the user's authority to operate

this equipment.

Toronto, Canada • Tech Line: 1-800-387-3630

www.dscgrp.com

29002462 R002