DSC WLS904P-433 Panduan Memulai Cepat

Jelajahi secara online atau unduh pdf Panduan Memulai Cepat untuk Sensor Keamanan DSC WLS904P-433. DSC WLS904P-433 2 halaman. Wireless motion detector

Halaman Cetak

Battery Installation

• This system is designed to work with Eveready Alkaline Energizer

This system is designed to work with Eveready Alkaline Energizer

Batteries. Do not install any other type. The reliability of the security system

Batteries.

depends on its batteries, and "no name" or generic brand batteries may

not provide the best quality and dependability.

• Use fresh batteries. Most batteries have a "best before" date printed on

their packaging or on the batteries themselves. Buy batteries that have a

"best before" date of two years or more from your purchase date.

• When disposing of used batteries, follow the instructions and precautions

printed on the batteries. Many cities and communities have collection sites

or services for used household batteries. Contact your municipal offices for

information on the disposal of used batteries.

Remove the motion detector from its mounting plate by holding the sensor by

its sides and pushing up. Install four fresh Eveready Alkaline Energizer AAA

batteries. Be sure to insert the batteries in

the proper orientation. Replace the sensor

on its mounting plate, making sure it snaps

into place.

After all the batteries are installed, the

detector will take 60 seconds to warm up.

During this time the LED will flash slowly.

FCC COMPLIANCE STATEMENT

CAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd. could void your authority to use

this equipment. This equipment generates and uses radio frequency energy and if not installed and used properly, in strict

accordance with the manufacturer's instructions, may cause interference to radio and television reception. It has been type tested

and found to comply with the limits for Class B device in accordance with the specifications in Subpart "B" of Part 15 of FCC

Rules, which are designed to provide reasonable protection against such interference in any residential installation. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to

television or radio reception, which can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

•

Re-orient the receiving antenna

•

Relocate the alarm control with respect to the receiver

•

Move the alarm control away from the receiver

•

Connect the alarm control into a different outlet so that alarm control and receiver are on different circuits.

If necessary, the user should consult the dealer or an experienced radio/television technician for additional suggestions.

The user may find the following booklet prepared by the FCC helpful: "How to Identify and Resolve Radio/Television

Interference Problems". This booklet is available from the U.S. Government Printing Office, Washington, D.C. 20402,

Stock # 004-000-00345-4.

Limited Warranty

Digital Security Controls Ltd. warrants that for a period of twelve months from the date of purchase, the product shall be free

of defects in material and workmanship under normal use and that in fulfilment of any breach of such warranty, Digital

Security Controls Ltd. shall, at its option, repair or replace the defective equipment upon return of the equipment to its repair

depot. This warranty applies only to defects in parts and workmanship and not to damage incurred in shipping or handling,

or damage due to causes beyond control of Digital Security Controls Ltd. such as lightning, excessive voltage, mechanical

shock, water damage, or damage arising out of abuse, alteration or improper application of the equipment.

The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any and all other warranties,

whether express or implied and of all other obligations or liabilities on the part of Digital Security Controls Ltd. This warranty

contains the entire warranty. Digital Security Controls Ltd. neither assumes, nor authorizes any other person purporting to act on

its behalf to modify or to change this warranty, nor to assume for it any other warranty or liability concerning this product.

In no event shall Digital Security Controls Ltd. be liable for any direct , indirect or consequential damages, loss of anticipated

profits, loss of time or any other losses incurred by the buyer in connection with the purchase, installation or operation or

failure of this product.

Warning: Digital Security Controls Ltd. recommends that the entire system be completely tested on a regular basis.

Digital Security Controls Ltd. recommends that the entire system be completely tested on a regular basis.

However, despite frequent testing, and due to but not limited to, criminal tampering or electrical disruption, it is

possible for this product to fail to perform as expected.

Toronto, Canada • www.dscgrp.com

Printed in Canada 29005105 R001

WLS904P-433

Wireless Motion Detector

INSTALLATION INSTRUCTIONS

The WLS904P is designed to combine the convenience of a wireless

detector with effective and reliable detection of human motion as well as

good protection against the nuisance alarms associated with pets weighing

up to 60 lbs (27.3 kg)

Installing The Detector

WLS904P provides effective immunity to single or multiple pets whose total

combined weight does not exceed 60 lbs. (27.3kg) when installed and

configured in the following manner.

Location

Select a detector location that will provide the coverage required and will allow

the detector to be mounted a minimum of 6 ½ ft (1.95m) high and not higher

than 10ft (3m) (7½ ft / 2.3m recommended)

Consider the following to avoid false alarms:

• Do not aim the detector at a stairwell to which a pet has access to.

• Do not place furniture or objects higher than 3ft (0.9m) which a pet can

climb onto (e.g. a cat on a couch), closer than 10ft (3m) from the detector.

• Mount the detector flat on a wall or in a corner. Do not angle it

downwards or use mounting brackets with this detector when it is used

in conjunction with pets.

• Do not aim the detector at reflective surfaces such as mirrors or

windows as this may distort the coverage pattern or reflect sunlight

directly onto the detector.

• Avoid locations that are subject to direct high air flow such as near an

air duct outlet.

• Do not locate the detector near sources of moisture such as steam or oil.

• Do not limit the coverage by large obstructions in the detection area

such as plants or cabinets.

When a location has been determined,

remove the plastic from the mounting

holes and locate the backplate on the

wall and mark screw locations. It is

suggested that wall anchors be used for

all screw locations. Secure the backplate

to the wall, and then secure the enrolled

Detector to its backplate.

information on the limitations as to liability of the manufacturer.

firealarmresources.com

(7½ ft / 2.3m recommended)

(7½ ft / 2.3m recommended).

(7½ ft / 2.3m recommended)

No detector should be mounted without first performing a module

placement test to determine that it is in range of the wireless receiver. . . . .

placement test to determine that it is in range of the wireless receiver

See the Placement Test instructions in the Instruction Sheet for your

See the Placement T

est instructions in the Instruction Sheet for your

See the Placement T

est instructions in the Instruction Sheet for your

receiver

receiver, or in the installation manual for your system.

receiver

, or in the installation manual for your system.

W A R N I N G

Please refer to the System Installation Manual for information

on limitations regarding product use and function and

ENSURE PROPER

ORIENTATION OF

BACKPLATE

MOUNTING HOLE

KNOCKOUTS

CORNER MOUNTING

KNOCKOUTS

MOTION DETECTOR BACKPLATE