DSE RE-BCC7L Panduan Pengguna

Jelajahi secara online atau unduh pdf Panduan Pengguna untuk Kamera Digital DSE RE-BCC7L. DSE RE-BCC7L 3 halaman.

Halaman Cetak

BCC7L

RE-RE-RE-BCC7R

BCC8L

USER MANUAL

Product Composition

Camera Cable

connection

power and video output

Support bracket

Cable for test video output

The camera

The RE-BCC camera belong to the category of

cameras in

protected housing with IR. They are very practical because

cameras can also be installed in harsh and outdoor

environments without the need for a protective case.

Power to the camera

On the back of the camera protrudes a

cable

power and video output. The video output can be recognized

by the typical bayonet BNC connector and may be connected

to the monitor or the video control device. At the power plug,

you must be connected to a 12VDC power supply with a 5.5

mm plug. center-positive, as the RE-AL5 model.

The AC power supply allows you to install the cameras

without protection (required if the power supply is 220V), as

well as

supply the camera with a battery in case of power failure.

Attention to use STABILIZED feeders that provide 12V in any

load condition. The use of a different supply voltage from

12VDC can generate video disorders and in the worst cases

damage the camera. Given

the

IR illuminator is necessary to pay close attention when the

wire

more than a few meters. Use appropriate sections in order to

avoid excessive voltage drop that would prevent proper

illuminating power of the LEDs.

Connect the video

The female BNC video connector must be connected to the

monitor or the video management device. If the distance to

be covered is a few meters you can use any type of cable.

But if you go over 10 meters we recommend using the

coaxial cable type RG59 or similar which also allows the

wiring over a hundred meters.

Audio output

RE-BCC cameras,

The

They have audio microphone, for obvious reasons of

protection against ingress of liquids. E ', however, can match

an external microphone like RE-CM2 model.

Target

This range of

AUTO IRIS equipped with varifocal lens. The AUTOIRIS

diaphragm adapts itself to light and allows outdoor shooting.

The focal point is from 6mm to 50mm variable in order to

obtain an optimum angle of view based on the area to be

framed.

Focus the lens.

The RE-BCC cameras last generation have the advantage of

being able to vary FOCAL (zoom) and FOCUS without

having to open them. The first thing to do after being linked

to video is finding the right visual varying the FOCAL, after

that it affects the focus until you get the picture well defined.

To do this the bottom of the camera near the mounting

bracket there are two controllers that provide the ability to

connectors:

vary FOCAL (zoom) and FIRE as illustrated in FIG.

IR Illuminator

The cameras of the RE-BCC series to integrate

illuminator 850 nm LED illuminator turns itself on when it gets

dark.

DSE srl - Digital Surveillance Equipment - www.dse.eu

significant uptake

D.C.

not

cameras

their

an internal

NOTE: Although infrared light is invisible to the human eye

LEDs, visas

dark assume a

to the

reddish brightness. Only the RE-BCC7R model

specially

manufactured not to emit any brightness even at a close

inspection and uses for this special LED lighting at 940 nm

Flow rate:

RE-BCC7R IR invisible RE 30 m-60 m BCC7L IR

RE-BCC8L IR 80 m The cameras of this series generate

lighting

infrared wide-angle that depending on the setting of the lens

focal ranges from 5 to 43 °

advanced settings

These cameras allow you to adjust the aperture iris and also

have the possibility to vary the intensity and the intervention

threshold of

LED. For

This round must open the lid placed next to the fire

regulators and zoom, then act on Trimmers using a

screwdriver. Inside this cover they are also present

some

signaling and additional VIDEO output to which is connected

the cable present in the package.

Trimmers:

LEVEL • used to

AUTOIRIS of the LED lens aperture ON • It used to adjust the

threshold

ignition

infrared CURRENT • It is used to adjust the intensity of

infrared LEDs. TO

higher intensity corresponds to a higher absorption.

LED (left to right):

PL • POWER LOW when the camera receives a voltage not

sufficient (<10.8V) the

lights PN • POWER NORMAL when the camera receives the

right 12V +/- 10% voltage turns on the green LED (from

10.8V to 13.2V) PO • POWER OVER when the camera

receives a too high voltage with respect to the normal one

will illuminate the RED LED. (> 13.2V) The camera in this

case goes to protection up to not give any image so as not to

be damaged.

VIDEO:

LED

regular

lED

lED yellow