Attero Tech AXON A4FLEX Panduan Pengguna - Halaman 9

Jelajahi secara online atau unduh pdf Panduan Pengguna untuk Aksesori Attero Tech AXON A4FLEX. Attero Tech AXON A4FLEX 13 halaman. Networked audio connectivity interface

Halaman Cetak

2.4 – LED Status Indications

The A4FLEX is equipped with various LED indicators. The

following chart indicates the available LED status information:

LED

Device Status

Booting

Critical error

Multiple

"Identify" mode

Firmware Update

Power on (OK)

PWR

No PTP sync

PTP sync – Slave

NET

PTP sync - Master

USB Host

USB

Connected

Ch1-Ch4 Input

Ch1-Ch3 Input,

Ch4 Output

Ch1,2 and 4

I/O

Input,

Ch 3 Output

Ch1-Ch2 Input,

Ch3-Ch4 Output

Signal below -

60dBFS

Signal between -

60dBFS and -

20dBFS

SIG

Signal between -

20dBFS and -

3dBFS

Signal above -

3dBFS

9 - Status Indicators

Status Indication

(LED)

Solid Yellow

(PWR / NET / USB / I/O LEDs)

Slow Blink Red

(PWR / NET / USB / I/O LEDs)

Slow Blink Whie

(PWR / NET / USB / I/O LEDs)

Fast Blink Blue

(PWR / NET / USB / I/O LEDs)

White

Solid Red

Solid Green

Solid White

White

(USB LED)

Off

Green

Blue

White

Off

Green

Yellow

Red

1315 Directors Row Suite 107 Fort Wayne, IN 46808 ⁞ (260)496-9668 ⁞ www.atterotech.com

– Device Configuration

The A4FLEX product is supported for setup and monitoring within

Attero Tech's unIFY Control Panel software. Additionally, QSYS

Designer plugins are available to provide seamless integration

with the QSYS DSP platform.

For a complete description of the A4FLEX software controlled

features found in unIFY Control Panel, consult the

software support resources

Refer to the support desk and

Tech website for the latest links to integration support resources.

3.1 – IP Address Setup

************************* IMPORTANT **************************

Failure to correctly configure IP addresses will not allow an

A4FLEX device to correctly authenticate in the unIFY Control Panel

software, and configuration and control to and from the A4FLEX

will not be possible.

*******************************************************************

In order to configure an A4FLEX or to update A4FLEX firmware, a

PC will need to be able to communicate with it over the network.

While all A4FLEX devices will be discovered regardless of the IP

address setup on the PC (the A4FLEX utilizes mDNS for device

discovery), full communication can only occur if the PC and the

device have compatible IP addresses.

By default, A4FLEX is set to get a dynamic IP address. If the

A4FLEX device does not find a DHCP server to retrieve an IP

address from, it will give itself a local link address (sometimes

also known as an automatic private IP address or APIPA) instead.

A local link address is always in the range 169.254.x.y.

To ensure communication, the PC can either be also set to get a

dynamic IP address, or be given a static IP address in the range

169.254.x.y. In some cases the PC

3.2– Networking Information

The A4FLEX uses the following IP addresses, services and ports

for communications on the network.

TCP /

Port

Mulitcast IP

UDP

224.0.0.251

5353

UDP

224.0.1.129

319-

320

UDP

N/A

49494

UDP

239.255.255.255

49495

10 - Ports and Protocols

for on the Attero Tech support desk.

A4FLEX product page

on the Attero

Description

N/A

DHCP

mDNS – Device

Disvovery

PTP – Clocking

(Domain 0)

A4FLEX control

A4FLEX status and

metering

on-line

Page 5