Atwood 85233 Panduan Instalasi dan Pengoperasian
Jelajahi secara online atau unduh pdf Panduan Instalasi dan Pengoperasian untuk Suku Cadang Mobil Atwood 85233. Atwood 85233 1 halaman. Disc brake actuators used for disc brake applications
Halaman CetakENGLISH, FRANÇAIS
REFER TO MPD 85778 FOR COMPLETE HYDRAULIC SURGE BRAKE INSTALLTION, OPERATION AND MAINTENEANCE INSTRUCTIONS.
SAFETY ALERT SYMBOLS
Safety Symbols alerting you to potential personal safety hazards. Obey all safety
messages following these symbols.
WARNING
avoid possible
injury or death
FOR YOUR SAFETY READ ALL INSTRUCTIONS
BEFORE INSTALLATION AND OPERATION
Installer:
Provide these instructions to the consumer.
Consumer: Keep documents for future reference.
SCHEMATIC REPRESENTATION OF HYDRAULIC CIRCUIT
INSTALLATION -
DISC BRAKE ACTUATOR SOLENOID BACK-UP VALVE
DEATH OR PERSONAL INJURY
•
This system requires the solenoid wire leads be connected
vehicle back-up light circuit.
8,000 LB. ACTUATORS
are equipped with a solenoid back-up valve.
1. Connect the solenoid valve wire leads to the tow vehicle back-up
light circuit.
2. Connect trailer brake line to actuator.
3. Bleed brake system.
6,000 LB. ACTUATORS
are not equipped with a solenoid back-up
valve. Contact Atwood (815-877-5700) for a Solenoid Back-up Valve
Kit - MPD 80376.
To install Atwood solenoid back-up valve -
1. Remove the plug in return port of master cylinder (this is the
upper port in the master cylinder).
2. Install straight barbed fitting (torque to 16-20 in/lb).
3. Install assembly in supply port of master cylinder (this is the lower
port in the master cylinder).
4. Connect the solenoid wire leads only into the reverse back-up
light circuit.
5. Connect trailer brake line to actuator.
6. Bleed brake system.
BRAKE FAILURE
•
use brake fluid drained from brake system in refilling master cylinder.
DO NOT
Brake fluid can be contaminated from the system.
9
(et Canada)
CAUTION
avoid possible
injury and/or property damage
WARNING
ONLY
CAUTION
LITERATURE NUMBER
DISC BRAKE ACTUATORS
USED FOR DISC BRAKE APPLICATIONS
INSTALLATION - BRASS ORIFICE FITTING
DAMAGE TO BRAKE ACTUATOR OR VEHICLE
• If brass orifice fitting is not installed, trailer-braking action may cause
vehicle(s) to shake during brake applications.
The brass orifice fitting installed in the master cylinder of the brake actuator
assembly must remain in the hydraulic circuit to the brakes of the trailer.
If the brass orifice fitting must be moved to accommodate plumbing for
a back up solenoid valve, it must be replaced in the hydraulic circuit in
line to brakes.
• Contaminated brake fluid in system could plug brass orifice fitting. This
could render brakes inoperative.
Be especially careful to clean all fittings, tubing and threads between
master cylinder and brass orifice fitting. A very small particle of dirt or
thread sealant can plug the hole in the orifice.
• Do not use Teflon
• If a liquid or paste thread sealant is used, keep it back two threads from end
of male fitting.
• Do not apply sealant to female threads. Clean female threads thoroughly.
BLEED BRAKE SYSTEM
1. Remove master cylinder filler cap and fill reservoir with DOT type 3
into the tow
or 4 automotive brake fluid.
2. Check all hydraulic line fittings & connections to make sure they are
leak free.
3. At brake assembly, connect a bleeder hose to bleeder fitting on wheel
cylinder and submerge free end in a container with brake fluid.
reuse brake fluid.
: Use power bleeder or bar with 2˝ diameter hitch ball attached.
NOTE
Do not use breakaway cable for purpose of bleeding brake system. If
a power bleeder is used air pressure 35 PSI is most effective.
: On tandem axle trailers, bleed brakes on rear most axle furthest
NOTE
from the actuator first.
4. Loosen bleeder fitting at top of brake assembly.
5. Apply actuator and tighten bleeder fitting. Return actuator to
forward position. Again, loosen bleeder valve and apply actuator.
Repeat this procedure until fluid expelled from bleeder hose is free
of air bubbles. It is helpful to lower the trailer tongue to promote air
bubble movement in the brake tubing. It is also helpful to tap gently
along the brake tubing during brake bleeding to keep air bubbles
from sticking to the inside of the brake tubing. During this
procedure, master cylinder reservoir fluid level must be maintained
at no less than 1/2 full and no more than 1/2˝ from top of reservoir.
6. When no air bubbles are visible, close bleeder valve securely and
remove bleeder hose.
7. Repeat
STEP
8. If installation is tandem axle with brakes on both axle, repeat
bleeding procedure on rear axle brakes for second time to assure
positive purging of all air in system.
9. After bleeding has been completed, re-check fluid level in master
cylinder.
MPD 85233
•Installation •Operation •Maintenance
CAUTION
WARNING
DEATH OR PERSONAL INJURY
™
tape on fittings.
1-6 for remaining brake, then brakes on forward axle.
Effective 12/04/07
DO NOT