3onedata IES6300-4GP2GS2HS-2DI2DO-2P48-60W Panduan Instalasi Cepat - Halaman 3
Jelajahi secara online atau unduh pdf Panduan Instalasi Cepat untuk Beralih 3onedata IES6300-4GP2GS2HS-2DI2DO-2P48-60W. 3onedata IES6300-4GP2GS2HS-2DI2DO-2P48-60W 5 halaman. Managed industrial ethernet switch
Halaman Cetak
17.
Gigabit SFP slot
18.
2.5G SFP slot
【Mounting Dimension】
Unit: mm
Note before mounting:
Don't place or install the device in area near water or
moist, keep the relative humidity of the device
surrounding between 5%~95% without condensation.
Before power on, first confirm the supported power
supply specification to avoid over-voltage damaging the
device.
The device surface temperature is high after running;
please don't directly contact to avoid scalding.
【DIN-Rail Mounting】
The product adopts 35mm standard DIN-Rail mounting which
is suitable for most industrial scenes, mounting steps as
follows:
Step 1
Check if the DIN-Rail mounting kit is installed firmly.
Step 2
Insert the bottom of DIN-Rail mounting kit (one side
with spring support) into DIN-Rail, and then insert
the top into DIN-Rail.
Tips:
Insert a little to the bottom, lift upward and then insert
to the top.
Step 3
Check and confirm the product is firmly installed on
DIN-Rail, then mounting ends.
【Disassembling DIN-Rail】
Step 1
Device power off.
Step 2
After lift the device upward slightly, first shift out the
top of DIN-Rail mounting kit, and then shift out the
bottom of DIN-Rail, disassembling ends.
Note before powering on:
Power ON operation: First insert the power supply
terminal block into the device power supply interface,
and then plug the power supply plug contact and power
on.
Power OFF operation: First, remove the power plug,
and then remove the wiring section of terminal block.
Please pay attention to the above operation sequence.
【Power Supply Connection】
DC power supply
The device provides 6-pin 5.08mm
pitch power supply terminal blocks. It
supports two independent DC power
supply systems, PWR1 and PWR2.
This series provides 34 products and
adopts 4 different power supply
ranges. Please notice the corresponding power supply type of
the device in case it damages the device.
24VDC PoE device
The power supply of 24VDC PoE device Model 3, Model 4,
Model 7, Model 8, Model 11, Model 12, Model 15, Model 16,
Model 25, and Model 30 has built-in 12A overcurrent
protection, support anti-reverse connection and redundant
backup. Power supply input 24VDC.
48VDC PoE device
The power supply of 48VDC PoE device Model 1, Model 2,
Model 5, Model 6, Model 9, Model 10, Model 13, Model 14,
Model 23, Model 24, Model 28 and Model 29 has built-in 5A
overcurrent protection, support anti-reverse connection and
redundant backup. Power supply input 48VDC.
12~48VDC non-PoE device
The power supply of 12~48VDC non-PoE device Model 18,
Model 20, Model 22, Model 27, Model 32 and Model 34 has
built-in 3A overcurrent protection, support non-polarity and
redundant backup. Power supply range: 12～48VDC.
AC power supply
The device provides 6-pin 5.08mm
pitch power supply input terminal
blocks and AC power supply system.
220VAC non-PoE device
The power supply of 220VAC non-PoE device Model 17,
Model 19, Model 21, Model 26, Model 31 and Model 33 has
built-in 5A overcurrent protection. Power supply range: 100～
240VAC.
【Relay Connection】
This device provides 6-pin 5.08mm pitch
input terminal blocks, and the relay
occupies the right 2 pins. Relay terminals
are a set of normally open contacts of the
device alarm relay. They are open circuit
in the state of normal non alarm, closed
when any alarm information occurs. For example, they are
closed when powered off, and send out alarm. The product
supports 1 relay alarm information output, which can be
connected to alarm light or alarm buzzer or other switching
value collecting devices; it can timely inform operators when
the alarm occurs.
【DIP Switch Settings】