3onedata IES6300PRO Series Panduan Instalasi Cepat - Halaman 4

Jelajahi secara online atau unduh pdf Panduan Instalasi Cepat untuk Beralih 3onedata IES6300PRO Series. 3onedata IES6300PRO Series 5 halaman. Layer 2 managed industrial ethernet switch

Halaman Cetak
LED digital tube
Note
status
it indicates that the switch is in
over-temperature alarm.
When the digital tube flashes
and displays the character "A",
it means that the switch is in
relay alarm state.
When
the
alternately
characters "E", "-","X" and "X",
it
means
corresponding port XX of the
switch
abnormally. For example, "01"
means port 1.
When
the
alternately
characters "F", "-","X" and "X",
it
means
corresponding port XX of the
switch sends data abnormally,
for example, "01" means port
1.
When the digital tube displays
the character "U", it means that
the USB flash drive is in place;
When it flashes, it means that
the USB flash drive is working,
and stops flashing after the
work is finished.
Note:
If it is detected that the number of sending or receiving
errors of a port does not exceed 20 within 1min, the
LED digital tube will not display the abnormal sending
and receiving status information of the port.
【Checking LED Indicator】
The series of devices provide LED indicators to monitor its
operating
troubleshooting process. The function of each LED is
described in the table below:
LED
P1-P2 / PWR
digital
tube
displays
the
that
the
RUN
receives
data
digital
tube
ALM
displays
the
that
the
LINK
(G1-G12/G20)
PoE
(G1-G8/G16)
【Logging in to WEB Interface】
This series of devices supports WEB management and
configuration, and computers can access devices through
Ethernet interfaces. The way of logging in to device's
configuration interface via IE browser is shown as below:
Configure the IP addresses of computer and the
device to the same network segment, and the
network between them can be mutually accessed
Enter device's IP address in the address bar of the
status,
which
has
simplified
the
Indicate
Description
Power
supply
is
ON
normally
Power supply is disconnected
OFF
or running abnormally
Device
is
not started
ON
abnormal
Blinking 1 time per second,
Blinking
system is running normally
The device is powered off or
OFF
the device is abnormal.
Power supply or port link has
ON
alarm
Power
supply,
port
OFF
without alarm
Ethernet port has established
ON
a valid network connection
Ethernet port is in an active
Blinking
network status
Ethernet
port
has
OFF
established
valid
connection
ON
POE port is powering other
PD devices normally
OFF
POE
is
disabled
disconnected
computer browser.
overall
Enter device's username and password in the login
window as shown below.
running
or
Click the "login" button. Change the initial password
when logging into the device for the first time, after
link
that, relog into the device's Web interface.
Note:
The default IP address of the device is "192.168.1.254".
The default user name and password of the device are
"admin".
not
When logging in to the device for the first time, the
network
system will prompt to change the initial password of the
default user; The length of the new password string
must be greater than or equal to 8 and be composed of
or
two or more kinds of uppercase letters, lowercase letters,
numbers and special characters.
If the user name or password is lost, the factory settings
can be restored through the DIP switch or management
software of the device; Or make a physical loopback
between Port 1 and Port 2 within the first minute when
the switch restarts.
Please refer to user manual for specific configuration
method of logging in to WEB interface and other
configurations about network management function.