Aube Technologies T1073 Panduan Pengguna

Jelajahi secara online atau unduh pdf Panduan Pengguna untuk Beralih Aube Technologies T1073. Aube Technologies T1073 2 halaman. 7-day solar programmable wall switch

Halaman Cetak

Applications

The TI073 programmable wall switch can be used in a single-switch or 3-way installation with the following

types of lighting:

• Incandescent

• Halogen

• Low-voltage halogen with transformer

The TI073 switch cannot be used with a load of less than 40 W or more than 500 W.

Installation

Cut power at the circuit breaker to avoid electric shock.

Remove the existing switch. (For a 3-way installation, identify and label the wire connected to the

"common" screw.)

Install the new switch (see the appropriate section below).

Apply power at the circuit breaker.

WARNING: Disconnect power to the switch when replacing a light bulb (see section 4).

SINGLE-SWITCH INSTALLATION

black

120

VAC

white

black

120

VAC

white

black

Connect the LINE and 3-WAY wires to the line (120 V) wire and LOAD wire to the load. Connect the GND

wire to a ground screw inside the electrical box.

EXISTING 3-WAY INSTALLATION

black

120

VAC

jumper

white

black

three-way

red

switch

Connect the LOAD wire on the TI073 to the "common" wire, which you identified when removing the old

switch. Connect the GND wire to a ground screw inside the electrical box. Connect the LINE and 3-WAY

wires to the two remaining wires. At the other 3-way switch, connect the jumper wire between the "common"

screw and the screw where the LINE wire of the TI073 is connected.

NEW 3-WAY INSTALLATION

black

120

VAC

white

TI073

• Fluorescent

black

yellow (3-WAY)

white

black (LINE)

green (GND)

black (LOAD)

yellow (3-WAY)

black (LINE)

green (GND)

black (LOAD)

black (LINE)

green (GND)

black (LOAD)

yellow (3-WAY)

white

black

black (LINE)

green (GND)

black (LOAD)

yellow (3 WAY)

white

Quick Start-up

Set the time and date before using the switch for the first time.

The TI073 will turn the lights on at sunset and turn them off at 11:00 pm by default. If these settings are

appropriate for you, you only need to set the time and date (see shaded zone in the menu flowchart sheet).

If the switch's sunset time does not correspond to the actual sunset time, see sections 5.3.3 and 5.3.4.

Operation

Indicates the mode of

operation (see Section 5.1)

Indicates the time and day

Indicates the current program

Indicates the load on/off state

Briefly press this button to turn the

lights on or off. See "Temporary

Override" in Section 5.1.4.

Press for 3 seconds to enter the

setup menus.

Before replacing a light bulb, pull out to disconnect power to the switch.

This prevents, while the bulb is out, any possible short circuit which will

damage the switch. Push back in after the light bulb is replaced.

Setup Menus

Press the main button for 3 seconds to enter the setup menus. Refer to

the menu flowchart sheet on how to navigate the menus.

(3 sec.)

5.1

Mode Menu

Use the Mode menu to select one of the three modes of operation (see sections 5.1.1 to 5.1.3).

5.1.1 Manual Mode

In Manual mode, the TI073 operates like a regular switch. To turn the lights on or off, briefly

press the main button. The

5.1.2 Automatic Mode

In Automatic mode, the TI073 turns the lights on or off according to the set programs (see

Section 5.4). The

icon as well as the current program number are displayed.

5.1.3 Random Mode

In Random mode, the TI073 has no specific times to turn the lights on or off. This mode is

designed to give the impression the house is occupied during your absence. It is similar to

the Automatic mode except there is no fixed program. The programs are automatically set

to different times by the TI073 every day. The

Random mode.

The first "On" program occurs at sunset. Each "On" program lasts between 1 hour and 1

hour and 30 minutes; each "Off" program lasts between 15 and 30 minutes. The last "Off"

program occurs between 10:30 pm and midnight.

5.1.4 Temporary Override

When the TI073 is in Automatic or Random mode, you can press the main button at any time to override the

single-pole

default state for the current program. The lights will turn off if they are on and vice versa. The new state icon

switch

(On or Off) flashes to indicate that the state is temporary. The new state is maintained until you press the

main button again or till the next "On" or "Off" program.

7-day Solar Programmable Wall Switch

The

icon indicates the current program

has been activated at sunset.

The

icon indicates the current program

has been activated at sunrise.

Press this button to display today's sunrise time.

Press this button to display today's sunset time.

The LED illuminates when the load state is on.

Safety switch

icon appears when the switch is in Manual mode.

icon appears when the switch is in

400-073-000-A

TI073

User guide

2009-01-28

1/2