Anywire BL296 B-16F Series Panduan Produk - Halaman 5

Jelajahi secara online atau unduh pdf Panduan Produk untuk Terminal sentuh Anywire BL296 B-16F Series. Anywire BL296 B-16F Series 11 halaman.
Juga untuk Anywire BL296 B-16F Series: Panduan Produk (17 halaman)

Halaman Cetak

[Address Number Setting]

1. Address number writing

- The address number to be set to the terminal is for correspondence to the input/output memory map of the controller.

This address number is the assigned rst position in the AnyWire input/output transmission frame (0 to 255). In the terminal, 16 points

(input or output) or 8 points (input/output mixed) are occupied after this number. In the case of input/output mixed type, the address

numbers for both input and output are the same.

- The address number can be set by one point.Set the address numbers so that the area occupied by the terminal does not exceed the

maximum transfer points.

- Use a dedicated address writer ARW-04 (Ver.04 to 1.01 or higher) or ARW-03 (Ver. 2.10 or higher) to write the address to be set in the terminal.

As for how to operate address writers ARW-04 (Ver.04 to 1.01 or higher) and ARW-03 (Ver. 2.10 or higher), refer to the product manual of the

address writer.

■ How to set

①Connect the AnyWireASLINK master and power supply to the transmission line of

　BL296□B-16F□-4A-20 to supply transmission signals and 24V DC.

②Operate the address writer to write address numbers with the address writer directed at the setting

　port of the main body (Fig. 2).

　(Hold the light receiving and emitting part as close as possible to the setting port.)

Address numbers settable with BL296□B-16F□-4A-20: Input or output

③In the case of writing in WRITE mode, reset the power supply of BL296□B-16F□-4A-20.

Transmission

signal

24V DC*

Make sure to use a 24V

DC stabilized power

supply for the power

supply to be connected.

CAUTION

2. Settings reading

When reading the address number which was written in the terminal, also use the address writer.

[Installation Method]

■ ADP-W96 (Installation dedicated DIN rail adapter)

The state in which the installation dedicated

DIN rail adapter is mounted and fixed in the

same direction as the DIN rail.

Red: DP

AnyWireASLINK

master

Black: DN

Green:

24V

24V DC*

The factory setting of the terminal is "255," which means no setting.

In this state, the terminal cannot perform an input/output operation.

Cross-section view A-A

41.90

-BL296*B16F*4A20 5/11-

0 to 240

0 to 248

Input/output mixed

Fig. 2

Setting port

(R/W)

(The port cannot

be seen from the

surface.)

White: 0V

41.90

CAUTION

1：24V

BL296SB-16F～

3：0V

1：24V

BL296XB-16F～

3：0V

1：24V

(Output side)

4：OUT

1：24V

BL296PB-16F～

3：0V

1：24V

4：OUT

1：24V

BL296SB-16FS～

3：0V

1：24V

BL296XB-16FS～

3：0V

(Output side)

4：OUT

1：24V

BL296PB-16FS～

3：0V

4：OUT

Make sure that no short circuit

occurs in the lines above.

Otherwise, a malfunction may occur.

Cross-section view A-A

The state in which the installation dedicated

DIN rail adapter is mounted and fixed in the

same direction as the DIN rail.