Dancing Wings Hobby 1.6M Fieseler Fi 156 Storch V2.0 Buku Petunjuk - Halaman 4
Jelajahi secara online atau unduh pdf Buku Petunjuk untuk Mainan Dancing Wings Hobby 1.6M Fieseler Fi 156 Storch V2.0. Dancing Wings Hobby 1.6M Fieseler Fi 156 Storch V2.0 9 halaman. Balsawood airplane
Halaman Cetak
03
像真件组装
Assemble the scale parts
天线
Antenna
03-1
此部位先不粘固
驾驶座
Do not glue this part at first
Pilot's seat
03-2
U13
U15
U14
U14
U16
橡胶套
Rubber sleeve
04
水平尾翼，垂直尾翼安装
Assemble the horizontal and vertical tails
04-1
04-2
切 开
Cut open
04-3
自攻螺丝
Self-tapping screws
另一边相同安装
Same installation
on the other side
注意 : 若您使用电动版本 此处斜撑建议不安装. 若您使用油动
版本.此处斜撑建议安装
Note: If you are building the electric version it is
recommended you do not install these struts. If building
the gasoline version then it is recommended to install
them.
副油箱
Auxiliary tank
03-3
碳管 2mm*51mm
Carbon Tube
U6
U2
U1
航灯
Navigation light
03-4
U5
U4
碳棒 Carbon rod 2mm*25mm
安装垂直尾翼与机身保持垂直，安装
水平尾翼与机身水平并居中，调整好
后再用胶水粘合固定。
The vertical tail is installed
perpendicular to the fuselage, and
the tailplane section is horizontal
to the fuselage Check the fit and
alignment then glue into place.
See note at end of manual.
04-4
方向舵，和升降舵通过纸合页连接到尾翼，如图所示。安装好后使舵面可以自由摆动。
The rudder and the elevator are connected to the tail parts with mylar hinges as
shown. Ensure you leave a small gap after installation so that the control surfaces
can move freely.
T3
L9
L8
支架拼装完成后，需打磨平滑，
L8
打磨时参考剖面L8形状。
L9
After the tail struts are
assembled they need to be
L10
sanded to shape. When
sanding refer to the shape of
part L8.
05
机翼安装
Assemble the Wing and Tail
05-1
碳管 6mm*170mm
Carbon Tube
碳棒 2mm*25mm
Carbon Rod
05-3
05-5
05-7
05-9
自攻螺丝
Self-tapping screws
自攻螺丝
Self-tapping screws
05-2
碳管 10mm*110mm
Carbon Tube
05-4
胶水粘合固定
Bond in place
with glue
T4
反面 Back
05-6
螺丝+螺母
Screw+blind nut
此处螺丝固定T1，螺丝拎到步骤
05-8
螺丝
01-1的爪牙螺母上。
Screw
Fit T1 here and screw it into
the blind nut of step 01-1.
螺丝
T1
Screw
另一边机翼相同步骤安装，安装完后机翼保持平直。
The other wing is installed in the same way. Please
ensure the wing remains straight after installation.
T5*2
此处自攻螺丝拧到步骤02-6细
节2的轻木条上。
Scew the self-tapping
screws into the hardwood
strip of 02-6 Detail 2.
碳管 6mm*600mm
Carbon Tube
顶面 top view
螺丝+螺母
Screw+blind nut
T1
T5*2
螺丝+螺母
Screw+nut
3