Duevi EZY-LAN Panduan Pengguna - Halaman 2

Jelajahi secara online atau unduh pdf Panduan Pengguna untuk Sistem Keamanan Duevi EZY-LAN. Duevi EZY-LAN 5 halaman. Wireless alarm panel with ethernet + wi-fi + gsm + lte
Juga untuk Duevi EZY-LAN: Manual (12 halaman), Panduan Pengguna (4 halaman)

Halaman Cetak
5 LED signals
The LEDs visible above the central button (1) (2)
(3) (4) provide information on the power supply
and connection status of the control unit.
When the control unit is powered by battery only
(no external power supply), in order to reduce
consumption, the LEDs (2) (3) (4) no longer give
any indication.
Led
Status
off
slow flashing
1 Power
quick flashing
steady on
off
quick flashing
2 Ethernet
steady on
off
slow flashing
3 Wi-Fi
quick flashing
steady on
off
slow flashing
4 GSM / LTE
quick flashing
steady on
6 Battery
The control unit is internally equipped with a
rechargeable lithium battery, which guarantees an
autonomy of up to 15 hours in the absence of an
external power supply.
When the battery level drops below the minimum
operating threshold, the control unit switches off
automatically, to preserve battery life. The
control unit automatically switches back on when
power is restored.
7 Control of the panel
The panel can be controlled by:
•
Keyfob / remote control
•
APP for smart devices
This is the privileged tool, thanks to which
you have complete control of the system in
real time.
•
SMS messages
8 Using the keyfob /remote control
Before being used, the remote control must have
been configured in the control panel by the
installer.
Indication
Panel turned off
No power supply +
battery ok
Power supply present
+ battery absent
Power supply present
+ battery ok
cable disconnected
cable connected +
internet / P2P absent
cable connected +
internet / P2P present
Module turned off
Wi-Fi access point
mode
Wi-Fi router mode +
internet / P2P absent
Wi-Fi router + internet
/ P2P mode present
Module turned off
SIM registered / GSM
mode
SIM not registered or
other problems
SIM registered / LTE
mode + internet / P2P
present
BUTTON + LED 1
BUTTON + LED 3
BUTTON + LED 5
Button 6 requests the system status from the
control panel and then displays:
TOTALLY ARMED
DISARMED
PARTIALLY ARMED
Buttons 1-2-3-4, when pressed briefly, perform
the operation for which they were programmed in
the control panel (arming, disarming, scenario
activation, etc)
Button 5, when pressed for at least 5 seconds,
can generate a panic alarm or a silent alarm (if
programmed in the control panel)
If the keyfob does not receive a response from the
control panel (e.g. because it is out of range) or
the control panel cannot carry out the command,
LEDs 5 and 6 flash simultaneously

9 Using the App

The control unit can be controlled via a dedicated
App available for IOS and Android systems on the
relevant stores.
The first time the App is run, the graphical
interfaces must be updated.
To connect to a control panel, it must be added to
the list of devices to be managed.
Enter SETTINGS -> MANAGE DEVICES and
perform one of the following actions:
•
SEARCH LOCAL DEVICES - automatically
searches for control panels connected to the
same local network to which the App device
is connected. In some cases, the modem /
router or the device itself may block this type
of request, so it will be necessary to proceed
with the manual addition (next point)
•
ADD WITH SERIAL / QR CODE - manually
enter the serial / scan the QR code on the
control panel label.
BUTTON + LED 2
BUTTON + LED 4
BUTTON + LED 6
Led 1/2/3/4 steady ON
Led 1/2/3/4 flashing
Led 1/2 steady ON
Led 3/4 OFF