Danfoss AK-CC55 Panduan Instalasi - Halaman 10

Jelajahi secara online atau unduh pdf Panduan Instalasi untuk Pengontrol Danfoss AK-CC55. Danfoss AK-CC55 18 halaman. Single coil
Juga untuk Danfoss AK-CC55: Panduan Instalasi (16 halaman)

Halaman Cetak
Danfoss AK-CC55 Panduan Instalasi

Menu survey

Menu set via display
Parameter
Function
Normal operation
Temperature (setpoint)
Thermostat
Differential
Max. limitation of setpoint setting
Min. limitation of setpoint setting
Temperature unit (°C/°F)
Correction of the signal from S4
Correction of the signal from S3
Manual service, stop regulation, start regulation (-1,
0, 1)
Displacement of reference during night operation
Define thermostat function
1=ON/OFF, 2=Modulating
Definition and weighting, if applicable, of thermostat
sensors - S4% (100%=S4, 0%=S3)
Time between melt periods
Duration of melt periods
Temperature setting for thermostat band 2 . As dif-
ferential use r01
Correction of the signal from S3B
Correction of the signal from S6
Definition and weighting, if applicable, of thermostat
sensors when night cover is on. (100%=S4, 0%=S3)
Heat function
Neutral zone between refrigeration and heat function
Time delay at switch between refrigeration and heat
function
Food type: use settings listed in table.
Min. limit for S4 temperature
Alarms
Delay for temperature alarm
Delay for door alarm
Delay for temperature alarm after defrost
High alarm limit for thermostat 1
Low alarm limit for thermostat 1
High alarm limit for thermostat 2
Low alarm limit for thermostat 2
High alarm limit for sensor S6 at thermostat 1
Low alarm limit for sensor S6 at thermostat 1
High alarm limit for sensor S6 at thermostat 2
Low alarm limit for sensor S6 at thermostat 2
R-W
If the operation is limited by a setting of one or more passwords, reading and setting the
parameter will be limited to:
R: This setting can be seen with password no. _ or higher.
W: This setting can be performed with password no. _ or higher (3 is the highest level).
*) Always required that the regulating is stopped, r12=0)
**) Always required that the regulating is stopped and set to manual service, r12= -1)
10 | AN294432763974en-000201
Wiring diagram pages 2-4
R-W Code
1
2 3
4
0-0
r00
1
1
1
1
1-2
r01
1
1
1
1
0-2
r02
1
1
1
1
0-2
r03
1
1
1
1
1-2
r05
1
1
1
1
1-2
r09
1
1
1
1
1-2
r10
1
1
1
1
0-2
r12
1
1
1
1
1-2
r13
1
1
1
1
1-2
r14
1
1
1
1
1-2
r15
1
1
1
1
1-2
r16
1
1
1
1
1-2
r17
1
1
1
1
0-2
r21
1
1
1
1
1-2
r53
1-2
r59
1
1
1
1
1-2
r61
1
1
1
1
1-2
r62
1-2
r63
1-2* r89
1
1
1
1
1-2
r98
1
1
1
1
1-2
A03
1
1
1
1
1-2
A04
1
1
1
1
1-2
A12
1
1
1
1
1-2
A13
1
1
1
1
1-2
A14
1
1
1
1
1-2
A20
1
1
1
1
1-2
A21
1
1
1
1
1-2
A22
1
1
1
1
1-2
A23
1
1
1
1
1-2
A24
1
1
1
1
1-2
A25
1
1
1
1
Min. value Max. value
5
6 7
8
9
1
1
1
1
1
"r03"
1
1
1
1
1
0.1 K
1
1
1
1
1
"r03"
1
1
1
1
1
-50 °C
1
1
1
1
1
0/°C
1
1
1
1
1
-10 K
1
1
1
1
1
-10 K
1
1
1
1
1
-1
1
1
1
1
1
-50 K
1
1
1
1
1
1
1
1
1
1
1
0 %
1
1
1
1
1
0 hrs
1
1
1
1
1
0 min.
1
1
1
1
1
-50 °C
1
1
-10 K
1
1
1
-10 K
1
1
1
1
1
0 %
1
0 K
1
0 min.
1
1
1
1
1
0
1
1
1
1
1
-50 °C
1
1
1
1
1
0 min.
1
1
1
1
1
0 min.
1
1
1
1
1
0 min.
1
1
1
1
1
-50 °C
1
1
1
1
1
-50 °C
1
1
1
1
1
-50 °C
1
1
1
1
1
-50 °C
1
1
1
-50 °C
1
1
1
-50 °C
1
1
1
-50 °C
1
1
1
-50 °C
SW = 2.0x
Factory
Actual
setting
setting
"r02"
2
20 K
2
50 °C
50
"r02"
-50
1/F
0/°C
10 K
0
10 K
0
1
0
50 K
0
2
1
100 %
100
10 hrs
1
30 min.
5
50 °C
2
10 K
0
10 K
0
100 %
100
50 K
5
240 min.
240
5
0
50 °C
-50
240 min.
30
240 min.
60
240 min.
90
50 °C
8
50 °C
-30
50 °C
8
50 °C
-30
50 °C
8
50 °C
-30
50 °C
8
50 °C
-30
© Danfoss | DCS (vt) | 2019.07