Dune 4WD 95L Dual Zone Panduan Produk - Halaman 8

Jelajahi secara online atau unduh pdf Panduan Produk untuk Pembeku Dune 4WD 95L Dual Zone. Dune 4WD 95L Dual Zone 11 halaman.

Halaman Cetak

Dune 4WD Fridge/Freezer

5. Maintenance And Product Care

Taking proper care of your Dune 4WD Fridge/Freezer is essential to ensure it

lasts for many years of trouble-free use. Here are some tips on maintenance,

product care and servicing:

Regularly defrost a er use: Each time you open your Dune 4WD Fridge/

•

Freezer lid, air enters the refrigeration compartment. When air comes in

contact with the cool wall of your fridge the water content will condense

out and – if the temperature is cold enough – the water will turn to ice.

Over time this ice can build up, which can cause damage to internal compo-

nents, reduce the efﬁciency of your fridge, and will turn to liquid when your

fridge is turned off, which can cause mould. Ensure ice does not build up

over time by following the steps below after each use:

•

Turn off your fridge freezer and disconnect from the power source.

•

Take off the lids and let the ice melt at room temperature.

•

Once the frost has melted, remove the drain plug to drain the liquid water

through the drain hole.

•

Wipe down the inner walls with a cloth.

•

Leave your fridge with the lid off in a dry, shady spot to dry out.

•

Remember to put the drain plug back in before use.

NOTE: Do not use sharp objects to remove ice. Do not leave your fridge in direct

sunlight.

Keep it clean: Regularly clean the inside and outside of your fridge with a

•

damp cloth. Avoid using harsh chemicals or abrasive cleaners as they can

damage the surface of the fridge. Once you have wiped down the fridge,

leave it in a shady, dry spot to dry out. Regularly wiping down the inside of

your fridge can remove grime, dirt and condensation from your fridge, whi-

ch can cause damage to internal components, reduce the efﬁciency of your

fridge, and cause mould and odour.

NOTE: Be sure to avoid wiping over the compartment temperature sensor di-

rectly, as this can damage the sensor.

Check the seals: The lid seals on your fridge are an important component

•

in keeping it cool. Make sure they are clean and free of debris and check

them regularly for any signs of wear or damage.

Store it properly: When not in use, store your fridge in a cool, dry place

•

with the lid off to allow air to circulate. This will help prevent mould and

mildew growth and keep the fridge in good condition. Remember to wipe

down your fridge before using it again.

•

Avoid marine environments: We recommend avoiding marine environments, as

salt can cause corrosion damage to electrical and metal components.

5. Maintenance And Product Care

Dune 4WD Fridge/Freezer

6. Error Codes and Troubleshooting

Error

Description Possible Cause

Code

Low

• Power cable

voltage

causing excessive

input

voltage drop

• Battery protection

level too high

• Power source

issue

Fan issue

Fan drawing too

much current

Compressor

• Compressor fault

start issue

• Compressor

module fault

Compressor

speed issue

6. Error Codes and Troubleshooting

Recommended Action

power cable supplied with your

device. Incorrect cabling can cause

excessive voltage drop, which can

reduce the voltage level at the input

to your fridge below the minimum

threshold.

2. Lower the battery protection level

to 'MED' or 'LOW'. Battery voltage

output reduces with use – your

power source may not be supplying

enough voltage to reach the restart

voltage level of the 'HIGH' protection

setting. If lowering the protection

level resolved the issue, consider

troubleshooting the original power

source.

3. Try a different power source (e.g.

power station, vehicle battery or

240V AC).

If changing the power

source resolved the issue, consider

troubleshooting the original power

source.

The fan must be replaced - contact

your local Anaconda store for

assistance.

1. Unplug for 10 minutes.

2. Try a different power source (e.g.

power station, vehicle battery or

240V AC). If changing the power

source resolved the issue, consider

troubleshooting the original power

source.

3. If still unresolved, contact your local

Anaconda store for assistance.

1. Unplug for 10 minutes.

2. Reduce amount of produce in

fridge.

3. If still unresolved, continue with E5

recommended actions.