Casio 2413-1 Berkenalan - Halaman 3

Jelajahi secara online atau unduh pdf Berkenalan untuk Menonton Casio 2413-1. Casio 2413-1 4 halaman.

Halaman Cetak

DEPTH GAUGE

The pressure sensor of the watch can also be used to take underwater depth

measurements while skin diving or snorkeling. Depth is displayed up to 30 meters (99

feet).

Important!

Never use this watch to measure depth while scuba diving.

Leaving the watch in the Depth Gauge Mode while not in the water uses up battery

power. Exit the Depth Gauge Mode whenever you are not using it.

See "Depth Gauge Mode" for more information.

Depth Gauge Mode Screen

Depth measurement starts after you enter the Depth Gauge Mode, with a new reading

taken every three seconds.

To perform a depth measurement

Just before starting your dive, press C to enter the Depth

Gauge Mode.

Depths are displayed in 0.1-meter (1-foot) units.

The mode indicator flashes while a measurement

operation is in progress.

The depth reading is automatically reset to zero

whenever you enter the Depth Gauge Mode.

The depth reading shows 0.0 meters (0 feet) when the

Depth value

watch is submerged at a depth of 0 to 1 meter (0 to 3

feet).

Mode indicator

You can change the unit of measurement for the

Timekeeping

displayed depth values between meters (M) and feet

Mode time

(F). See "To specify the depth measurement unit".

When a depth of 30 meters (99 feet) is exceeded, the message

the display. The depth value reappears when the depth reading returns to the

measurable range.

Enters the Depth Gauge

Mode (Measurement start)

Depth = 1 meter

(3 feet)

Note

You cannot exit the Depth Gauge Mode while any reading other than 0.0 meters (or

feet) is on the display. See "Depth Gauge Measurement Precautions" for more

information.

Depth Gauge Mode Graphic Indicator

In the Depth Gauge Mode, the graphic indicator shows

Graphic indicator

the current depth. The first bar appears on the right of the

(Indicates 5m)

indicator when depth reaches 1 meter (3 feet). One more

bar appears with each additional 1 meter (3 feet) of depth,

up to 30 meters (99 feet).

You can set a Daily Alarm that sounds at the same time

each day, while the alarm is turned on. You can also turn

on an Hourly Time Signal that causes the watch to beep

twice every hour on the hour.

All of the operations in this section are performed in the

Alarm Mode, which you enter by pressing C.

To set the alarm time

Alarm time

1. In the Alarm Mode, hold down A until the hour digits of

(Hour : Minutes)

Mode

the alarm time start to flash, which indicates the setting

indicator

screen.

Alarm on indicator/

Displaying the alarm time setting screen turns on the

Hourly time signal

Daily Alarm.

on indicator

2. Press C to move the flashing between the hour and minute's digits, and then use

D (+) to change the flashing digits.

When setting the alarm time using the 12-hour format, take care to set the time

correctly as am (no indicator) or pm (P indicator).

3. Press A to exit the setting screen.

Daily Alarm Operation

The alarm sounds at the preset time each day for about 20 seconds (in all modes) or

until you stop it by pressing any button.

To test the alarm

In the Alarm Mode, hold down D to sound the alarm.

To turn the Daily Alarm and Hourly Time Signal on and off

In the Alarm Mode, press D to cycle through the on and off settings as shown below.

[Alarm On indicator/Hourly Time Signal On indicator]

Daily Alarm

Hourly Time

Only

Signal only

FULL

appears on

Display: 0

Display:

Actual depth

ALARM

Both On

Both Off

STOPWATCH

The stopwatch lets you measure elapsed time, split times,

and two finishes.

The display range of the stopwatch is 23 hours, 59

minutes, 59.99 seconds.

The stopwatch continues to run, restarting from zero

after it reaches its limit, until you stop it.

The stopwatch measurement operation continues even

if you exit the Stopwatch Mode.

Hours

Seconds

All of the operations in this section are performed in the

Minutes

Stopwatch Mode, which you enter by pressing C.

Mode

1/100 second

indicator

To measure times with the stopwatch

Elapsed Time

Start

Stop

Split Time

Start

Split

Two Finishes

Start

Split

First runner

finishes.

Display time of

first runner.

REFERENCE

This section contains more detailed and technical information about watch operation.

It also contains important precautions and notes about the various features and

functions of this watch.

Sensor Data Errors

Whenever a sensor problem, poor electrical contact, or

other abnormality occurs during a barometric pressure,

altitude, or depth measurement operation, the watch

beeps for about three seconds and the ERROR indicator

starts to flash on the display to indicate a sensor error. All

measurement operations are disabled while the ERROR

indicator is on the display.

If the ERROR indicator appears, press C to change to

another mode, and then return to the mode where the

error occurred. If the ERROR indicator appears again, it

could mean that the watch is malfunctioning. Contact the

store or dealer where you purchased the watch.

Low Battery Indicator

If the cause of the low battery indicator is due to cold

conditions (about –10 C/14 F), normal operation should

return after the watch is brought back to normal

temperature.

If the cause of the low battery indicator is due to low

battery power (indicated when BATT appears under

normal temperatures), you should have the watch's

batteries replaced as soon as possible.

Auto Return Features

After you perform an operation in any mode, pressing C returns to the Timekeeping

Mode.

If you leave the watch for about one hour without performing any button operation in

the Barometer Mode or Altimeter Mode, or in the Depth Gauge Mode with a current

depth reading of 0, the watch beeps and returns to the Timekeeping Mode.

If you leave a screen with flashing digits on the display for two or three minutes

without performing any operation, the watch saves anything you have input up to

that point and exits the setting screen.

Setting Scrolling

The D and B buttons are used in various setting screens to scroll through settings

on the display. In most cases, holding down either of these buttons scrolls through

settings at high speed.

12-hour/24-hour Timekeeping Formats

The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is also

applied in all modes.

With the 12-hour format, the P (PM) indicator appears to the left of the hour digits for

times in the range of noon to 11:59 p.m. and no indicator appears to the left of the

hour digits for times in the range of midnight to 11:59 a.m.

With the 24-hour format, times are displayed in the range of 0:00 to 23:59, with 24H

indicator.

2413-3

Re-start

Stop

Split release

Stop

Split release

Second runner

Display time of

finishes.

second runner.

Clear