Casio 2532 Panduan Pengoperasian - Halaman 3

Jelajahi secara online atau unduh pdf Panduan Pengoperasian untuk Menonton Casio 2532. Casio 2532 5 halaman.

Halaman Cetak

To set an alarm time

1. In the Alarm Mode, use D to scroll through the alarm

screens until the one whose time you want to set is

displayed.

ON or OFF

• You can configure Alarm 1 as a snooze alarm or a one-time alarm. Alarms 2

through 5 can be used as one-time alarms only.

• The snooze alarm repeats every five minutes.

2. After you select an alarm, hold down A until the hour setting of the alarm time

starts to flash. This indicates the setting screen.

3. Press C to move the flashing between the hour and minute settings.

4. While a setting is flashing, use D (+) and B (–) to change it.

• When setting the alarm time using the 12-hour format, take care to set the time

correctly as a.m. (no indicator) or p.m. (P indicator).

5. Press A to exit the setting screen.

Alarm Operation

The alarm sounds at the preset time for about 10 seconds. In the case of the snooze

alarm, the alarm operation is performed a total of seven times, every five minutes, until

you turn the alarm off or change it to a one-time alarm.

The watch also has a brightness alarm. When turned on, the brightness alarm causes

the watch to beep for 10 seconds when the watch is brought from the dark into the

light. The following are the conditions for brightness alarm operation.

• The watch needs to be in the dark for about 30 to 35 minutes for the brightness

alarm to become activated.

• The brightness alarm sounds about 15 to 20 minutes after the watch is next exposed

to light.

• The brightness alarm sounds only once and then turns off automatically.

Note

• Pressing any button stops the alarm tone operation.

• Performing any one of the following operations during a 5-minute interval between

snooze alarms cancels the current snooze alarm operation.

Displaying the Timekeeping Mode setting screen

Displaying the Alarm 1 setting screen

To test the alarm

In the Alarm Mode, hold down D to sound the alarm.

To turn Alarms 2 2 2 2 2 through 5 5 5 5 5 on and off

1. In the Alarm Mode, use D to select a one-time alarm

One-time alarm on

(alarm number 2 through 5).

indicator

2. Press B to toggle the displayed alarm on and off.

• Turning on a one-time alarm (2 through 5) displays the

one-time alarm on indicator (ALM) on its screen.

• The one-time alarm on indicator is displayed in all

modes.

• If any alarm is on, the alarm on indicator is shown on

the display in all modes.

To select the operation of Alarm 1 1 1 1 1

1. In the Alarm Mode, use D to select Alarm 1.

2. Press B to cycle through the available settings in the sequence shown below.

SNZ indicator and one-time alarm on indicator

ALM

SNZ ALM

One-time alarm on

Snooze alarm on

• The applicable alarm on indicator (ALM or SNZ ALM) is displayed in all modes

when an alarm is turned on.

• The SNZ indicator flashes during the 5-minute intervals between alarms.

• Displaying the Alarm 1 setting screen while the snooze alarm is turned on

automatically turns off the snooze alarm (making Alarm 1 a one-time alarm).

To turn the hourly time signal and the brightness alarm on and off

1. In the Alarm Mode, use D to select the Hourly Time

Hourly time signal on

Signal or the brightness alarm.

indicator

2. Press B to toggle the displayed item on and off.

• Turning on the Hourly Time Signal displays the hourly

time signal on indicator (SIG) on its screen.

• Turning on the brightness alarm displays the brightness

alarm on indicator (BRT) on its screen.

• The hourly time signal on indicator and brightness alarm

on indicator are displayed in all modes.

Brightness alarm on

indicator

Stopwatch

The stopwatch lets you measure elapsed time, split times,

Minutes

and two finishes.

• The display range of the stopwatch is 99 hours, 59

Hours

Seconds

minutes, 59.99 seconds.

• The stopwatch continues to run, restarting from zero

after it reaches its limit, until you stop it.

• The stopwatch measurement operation continues even

if you exit the Stopwatch Mode.

• Exiting the Stopwatch Mode while a split time is frozen

on the display clears the split time and returns to

1/100 second

elapsed time measurement.

• All of the operations in this section are performed in the

Stopwatch Mode, which you enter by pressing C.

Operation Guide 2532

:00

Alarm off

To measure times with the stopwatch

Elapsed Time

➤

Start

Stop

Re-start

Split Time

➤

Start

Split

Split release

(SPL displayed)

Two Finishes

➤

Start

Split

Stop

First runner

Second runner

finishes.

Display time of

first runner.

Dual Time

The Dual Time Mode lets you keep track of time in a

Dual time

different time zone.

(Hour : Minutes Seconds)

• The seconds count of the Dual Time is synchronized

with the seconds count of the Timekeeping Mode.

To set the Dual Time

1. Press C to enter the Dual Time Mode.

2. Use A, B, and D to set the Dual Time Mode time.

• Each press of D (+) and B (–) changes the time

setting in 30-minute increments.

• Pressing A sets the Dual Time Mode to the same time

Timekeeping Mode time

as the Timekeeping Mode.

Backlight

The backlight uses an EL (electro-luminescent) panel that

Auto light switch

causes the entire display to glow for easy reading in the

on indicator

dark. The watch's auto light switch automatically turns on

the backlight when you angle the watch towards your face.

• The auto light switch must be turned on (indicated by

the auto light switch on indicator) for it to operate.

• See "Backlight Precautions" for other important

information about using the backlight.

To turn on the backlight manually

In any mode, press L to illuminate the display for about

one second.

• The above operation turns on the backlight regardless of

the current auto light switch setting.

About the Auto Light Switch

Turning on the auto light switch causes the backlight to turn on for about one second,

whenever you position your wrist as described below in any mode. Note that this

watch features a "Full Auto EL Light," so the auto light switch operates only when

available light is below a certain level. It does not turn on the backlight under bright

light.

Moving the watch to a position that is parallel to the ground and then tilting it towards

you more than 40 degrees causes the backlight to turn on.

Parallel to

ground

Warning!

• Always make sure you are in a safe place whenever you are reading the

display of the watch using the auto light switch. Be especially careful when

running or engaged in any other activity that can result in accident or injury.

Also take care that sudden illumination by the auto light switch does not

surprise or distract others around you.

• When you are wearing the watch, make sure that its auto light switch is turned

off before riding on a bicycle or operating a motorcycle or any other motor

vehicle. Sudden and unintended operation of the auto light switch can create a

distraction, which can result in a traffic accident and serious personal injury.

To turn the auto light switch on and off

In the Timekeeping Mode, hold down D for about two seconds to toggle the auto light

switch on (AUTO EL displayed) and off (AUTO EL not displayed).

• The auto light switch on indicator (AUTO EL) is on the display in all modes while the

auto light switch is turned on.

Battery

This watch is equipped with a solar cell and a rechargeable battery (secondary

battery) that is charged by the electrical power produced by the solar cell. The

illustration shown below shows how you should position the watch for charging.

Example: Orient the watch so its

face is pointing at a light source.

• Note that charging efficiency

drops when any part of the solar

cell is blocked by clothing, etc.

• The illustration shows how to

position a watch with a resin band.

Important!

• Storing the watch for long periods in an area where there is no light or wearing it in

such a way that it is blocked from exposure to light can cause rechargeable battery

power to run down. Be sure that the watch is normally exposed to bright light

whenever possible.

➤

Stop

Clear

➤

Stop

Clear

➤

Clear

Split release

Display time of

second runner.

More than

40°

Solar cell