AudioSource AD1002 Panduan Pemilik - Halaman 3

Jelajahi secara online atau unduh pdf Panduan Pemilik untuk Penguat AudioSource AD1002. AudioSource AD1002 4 halaman.

Halaman Cetak

FRONT PANEL CONTROLS

1. Power Switch

Switches the AMP100VS on or off. A red LED indicates connection to AC

power while in standby mode. Turns green indicating audio signal is present.

2. Speaker Selector

Selects speaker zone A or B. For A + B zones push both buttons in.

REAR PANEL CONTROLS

6. Bass and Treble Controls

These controls can adjust bass and treble frequencies +/- 12dB at 100Hz

and 10kHz.

7. Interupting Line Input

This is the secondary input, use MAIN IN for your main input.

INTERRUPTING INPUT can be used if a second source is desired and

takes over when signal is present and has at least a 5mV level.

When there is no signal, or a signal with less than 5mV level, the amp

switches back to MAIN IN after a brief delay.

Main Input/Output

MAIN IN should be used as the "primary" or main input for the ampliﬁer.

Connect your receiver or main source to this input. Use MAIN OUT to pass

MAIN IN signal to another amplifier.

9. 12V Trigger

Allows the AMP100VS to be powered on by other electronics or to power

on other electronics via a 3.5mm mini phone plug cable.

10.

Mode Select Switch

Switches the ampliﬁer from Stereo mode to Bridged mode.

STEREO MODE

If you will be connecting one or two pair of speakers to the ampliﬁer, place

the switch in the "Stereo" position. NOTE: For playing 2 pairs of speakers

(A plus B), make sure each speaker has an impedance of 8 ohms or greater.

BRIDGED MODE

When set to "Bridged" mode, the ampliﬁer is a single channel mono amplifier.

BRIDGED MODE- MONO APPLICATION

For bridged mode, playing Right and Left together as mono output, use a

Y cable adapter to connect Right and Left RCA signal to the Right (Red) input

at MAIN IN. Set the MODE switch to BRIDGED and follow the instructions

for bridged speaker connection in the SPEAKER TERMINALS section of

this manual.

NOTE: The AMP100VS supplies 150W in bridged mode, Please verify that your

speakers are capable of handling such power to avoid possible damage!

11.

AUTO ON Select Switch

Power can be turned on and off manually via the switch on the front panel

or automatically by signal sensing. Set it to NORMAL for manual power on/off.

Set to AUTO for signal sensing; the amp will turn on when audio signal is

detected at the inputs. NOTE: The front panel power switch must be in the

ON position (pushed in) for the AUTO ON feature to operate.

12.

Speaker Zone A Output

Speaker output terminals for zone A. Minimum impedance: 8 ohm bridged

or 4 ohm stereo.

13970 SW 72nd Ave, Portland, OR 97223 • 503.914.4688 • www.audiosource.net

Connect

Receiver

Here

3. Balance

Fades speaker output between the Right and Left Channels

4. Volume

Adjusts ampliﬁer volume.

13.

Speaker Zone B Output

Speaker output terminals for zone B. Minimum impedance: 8 ohm bridged

or 4 ohm stereo.

SPEAKER TERMINALS - STEREO MODE

For stereo output connect the speaker's positive (red) terminal to the ampliﬁer's

positive (red) terminal, and the speaker's negative (black) terminal to the

ampliﬁer's negative (black) terminal for each Right and Left speaker.

SPEAKER TERMINALS - BRIDGED MODE

Place the "MODE" switch in the "BRIDGED" position and use both red

terminals to connect to the speaker. Connect the speaker's positive (red)

terminal to the ampliﬁer's red (+) terminal noted next to the bridging mark, and

the speaker's negative (black) terminal to the ampliﬁer's unmarked positive

(red) terminal.

NOTE: Only one zone (A or B) can be bridged. Do not attempt to bridge both

A and B speaker terminals! This may result in a lower impedance than the

ampliﬁer is designed for and may damage your ampliﬁer. The minimum

impedance for the total load connected in bridged mode is 8 ohms.

NOTE: Use Class 2 wiring for speaker connections.

To wire the output connector: 1. Strip the insulation off each speaker wire to expose 3/8"

(10 mm) of bare conductor. 2. Unscrew the output terminal binding post several twists,

insert each wire into the correct terminal. 3. Tighten binding post by twisting clock-wise

until it is firmly clamping the speaker wire.

Warning: While the amplifier does self-protect under most improper output conditions,

misconfiguration of loudspeaker mode and incorrect connection of loudspeakers could

damage connected loudspeakers and/or amplifier.

Please refer installation to a qualified installation professional, and always check state and

local electrical codes when installing.

NOTE: To prevent sonic degradation in your speaker installation, total speaker

wire resistance should be kept below 0.5 ohms. This table lists recommended

speaker wire gauge versus wire run length.

50' or less - 16 Gauge 2-Cond. CL3 Rated

50' - 150' - 12 Gauge 2-Cond. CL3 Rated

150' - 200' - 10 Gauge 2-Cond. CL3 Rated

14. Unswitched A/C Terminal

Provides A/C power for additional components. Use only for a single low

power device such as a tuner, CD, DVD, turntable or other non-amplified

electronics. Do not connect another amplifier or receiver. Ensure 400W

max power connumption for any device plugged in here.

15.

Power Cord & Fuse Holder

This ampliﬁer is conﬁgured for operation at 117V (North America). A fuse

in the integrated holder provides safety protection from fault conditions.

Replace fuse with 5 x 20mm T4A 250V.

AMP100VS

OWNER'S MANUAL

Figure 1. Front Panel

Figure 2. Rear Panel