Contemporary Research QMOD-HDMI RGB Panduan Produk - Halaman 9

Jelajahi secara online atau unduh pdf Panduan Produk untuk Penguat Contemporary Research QMOD-HDMI RGB. Contemporary Research QMOD-HDMI RGB 17 halaman. Hd modulator-iptv encoders
Juga untuk Contemporary Research QMOD-HDMI RGB: Panduan Instalasi (11 halaman), Panduan Produk (16 halaman)

Halaman Cetak

Advanced

This series of menus sets global values for QMOD operation.
A-Pgm Number
Sets a specific Program number 1-65535, default is 1 for A, 2 for B.
A-Source ID
Sets Source ID 1-65535, Often used to match program number for emulating Guide channel in cable systems.
A-Bitrate Mode
Only visible when QMOD outputs on Ethernet only. Selects Constant or Variable rate
A-QMODIPPort
Sets Source IP port for streaming (2728 default)
A-Mcast TTL
Time To Live function assures that multicast streams don't loop forever when they're not being used.
0-255 - Typical settings:
A-AVDropped
Counts the number of frames dropped for testing, press right arrow to clear
A-MPEG2DcDly
Sets encoding MEPG2 delay from 200 to 500 ms. Note that the internal buffer adds 150 ms, and typical
decoding delay for TVs is about 150 ms, so end-to-end latency is about 500 ms.
A-MPEG4DcdDly
Sets encoding MPEG4 delay from 300-500 ms. See above.
B-Pgm Number
Sets a specific Program number 1-65535, default is 1 for A, 2 for B.
B-Source ID
Sets Source ID 1-65535.
B-Bitrate Mode
Only visible when QMOD outputs on Ethernet only. Selects Constant or Variable rate
B-QMODIPPort
Sets Source IP port for streaming (2728 default)
B-Mcast TTL
0-255 This Time To Live function assures that multicast streams don't loop forever.
B-AVDropped
Counts the number of frames dropped for testing, press right arrow to clear
B-MPEG2DcDly
Sets encoding MEPG2 delay from 200 to 500 Ms. Average TV decoding delay is 150 Ms.
B-MPEG4DcdDly
Sets encoding MPEG4 delay from 300-500 Ms
Fan speed in percent, operation is automatic
Fan Speed
Temperature
Processor temperature, tends to hover around 139 degrees
EAS Video
Selects video input to use when an Emergency Alert has been triggered, may be any input
EAS Audio
Selects audio input to use when an Emergency Alert has been triggered, may be any input
IP TS Mode
Sets SPTS or MPTS for IPTV streaming. Setting to MPTS will change A and B IP port to one address, using the
most recent setting.
CVCT
Activates inclusion of virtual channel ID and short Name in the video stream.
On (default) | Off
23 (default)
Telnet Port
IP port for Telnet communication – Click or hold Up or Down to set.
Setup Lockout
On or Off On locks out Setup button
Pressing Setup and the Right key will unlock Setup until the QMOD is reset.
Custom Reset – saves current settings to use for Reset
Save Data
Reset
Select Factory Default or Custom settings
Auto | 100 Mbps
IP Speed
Reboot
Left or Right arrow cycles between Reboots, AV Dropped, FIFO Full counts, reset counters from Web page

Web Pages

Contemporary Research
0- restricted to the same host, will not be forwarded by any interface
1-restricted to the same subnet, won't be forwarded by router
32-(default) restricted to the same site
64- restricted to the same region
128- restricted to the same continent
You can also access all the settings via the onboard Web pages. Access by
pointing your browser to the unit's IP address. Or use the front-panel USB port
this way:
•
Go to Control Panel /Network and Sharing Center/Change Adapter Settings
•
Right-click on the USB Ethernet/RNDIS Gadget, and right-click Properties
•
Select Internet Protocol Version 4, select Properties and enter
•
Enter 192.168.227.227 in your browser to see the QMOD web pages
•
Once this is set, the same settings apply to all QMODs
9
o
IP Address: 192.168.227.1
o
Subnet mask: 255.255.255.0
QMOD Modulators HD/IPTV Encoders