Appalachian Stove & Fabricators UV-EF-MIL 30-N Panduan Petunjuk Pemasangan dan Pengoperasian - Halaman 6
Jelajahi secara online atau unduh pdf Panduan Petunjuk Pemasangan dan Pengoperasian untuk Perapian Dalam Ruangan Appalachian Stove & Fabricators UV-EF-MIL 30-N. Appalachian Stove & Fabricators UV-EF-MIL 30-N 11 halaman. Gas log heaters
Halaman Cetak
FOR YOUR SAFETY READ BEFORE LIGHTING
WARNING: If you do not follow these instructions exactly, a fire or explosion may
Result causing property damage, personal injury or loss of life.
This appliance has a pilot which must be
A.
lighted by hand. When lighting the pilot, follow these
instructions exactly.
B. BEFORE LIGHTING smell all around the
appliance area for gas. Be sure to smell next to the
floor because some gas is heavier than air and will
settle on the floor.
WHAT TO DO IF YOU SMELL GAS:
DO NOT TRY TO LIGHT ANY APPLIANCE.
DO NOT TOUCH ANY ELECTRICAL
SWITCH; DO NOT USE ANY PHONE IN YOUR
BUILDING.
IMMEDIATELY CALL YOUR GAS SUPPLIER
1. STOP! Read the safety information above.
2. Push in gas control knob slightly and turn clockwise
"OFF." NOTE: Knob cannot be turned from "PILOT" to
"OFF" unless the knob is pushed in slightly. Do not force.
3. Wait five (5) minutes to clear out any gas. If you smell gas,
STOP! Follow "B" in the safety information above. If you don't
smell gas, go to the next step.
4. Find pilot located between the front log and the second log.
5. Turn the control knob counterclockwise
6. Push the control knob all the way in and hold in. While still
holding the control knob in, push the Piezo Ignitor button
several times. This will cause a spark at the pilot which should
ignite the pilot gas. Continue to hold the control knob in for
several seconds to prevent flame failure.
7. Release the control knob.
*If the control knob does not pop back up when
released, stop and immediately call your service
technician or gas supplier.
*If the pilot does not stay lit after several tries, turn the
gas control to OFF and call your service technician or
gas supplier.
TO TURN OFF GAS TO APPLIANCE
To turn off the gas appliance
1. From the "ON" position, turn the control knob clockwise
pilot will remain lit.
2. If complete shut down is desired from the "PILOT" position, push in the control knob slightly and turn clockwise
"off" position. Do not force the knob.
LIGHTING INSTRUCTIONS
to
to pilot.
FROM A NEIGHBOR'S PHONE. FOLLOW
YOUR GAS SUPPLIER'S INSTRUCTIONS.
IF YOU CANNOT REACH YOUR GAS
SUPPLIER, CALL THE FIRE DEPARTMENT.
C. Use only your hand to push in or turn the gas
control knob. Never use tools. If the knob will not push
in or turn by hand, don't try to repair it, call a qualified
service technician. Force or attempted repair may
result in a fire or explosion.
D. Do not use this appliance if any part has
been under water. Immediately call a qualified service
technician to inspect the appliance and to replace any
part of the control system and any gas control which
has been underwater.
8. Once the pilot remains lit, depress the gas control knob slightly
and turn the gas control knob counterclockwise
NOTE: The "ON/OFF" SWITCH is used to turn the flame on or
off when the control valve is in the "ON" position.
IMPORTANT: DO NOT OPERATE BETWEEN SETTINGS
This appliance is fitted with a transient pilot burner for the sole
purpose of safe, momentary ignition of the main burner in
conjunction with the piezo ignitor. When in operation with the
main burner, it contributes to the base heat release and is turned
off by turning the control knob to the off position.
9. Periodically check the pilot flame for proper flame pattern.
MATCH LIGHTING
If the pilot cannot be ignited with the piezo, it can be manually lit
with the use of a paper match and a lighter rod. Place the match
in the holder and light. With the right hand, depress and turn the
control knob counterclockwise
in.
Take the rod and lit match and light the pilot. The pilot is located
behind the front and the second log.
Continue to hold the control knob for an additional 10 seconds to
ensure that the pilot is maintained.
Control Knob
Piezo Ignitor
Piezo
to the "PILOT" position. The log set will extinguish, and the
to "ON."
to the pilot position and hold
HI/LO KNOB
OFF
OFF
to the
6