AddSecure IRIS-4 2 Series Panduan Instalasi dan Pemeliharaan Cepat - Halaman 8

Jelajahi secara online atau unduh pdf Panduan Instalasi dan Pemeliharaan Cepat untuk Sistem Keamanan AddSecure IRIS-4 2 Series. AddSecure IRIS-4 2 Series 9 halaman.

Halaman Cetak

IRIS-4

2 Series

Quick Installation and

Maintenance Guide

8. SPeCIFICatIonS

transmission paths

200

Ethernet

Standard

–

Connection

–

IP addressing

–

Fault detection

–

2/3/4G

Frequencies

Penta band LTE (4G)

800/900/1800 MHz

2100/2600 MHz

Dual band UMTS (3G)

900/2100 MHz

Dual band GSM (2G)

900/1800 MHz

Connection

SMA socket for antenna

Fault detection

Loss of registration with network

TCP ports (outbound)

53165 (Alarms & Polling), 51292 (Diagnostic & Reflashing), 10001 (Upload/Download)

Alarm transmission

Interface to

IRIS Secure Apps or IRIS Management Suite

Monitoring Centre

via EN 50136-2 pass-through mode

Dial capture interface

Two wire interface via terminal block

to alarm panel

Serial interface to

RS485, TTL, RS232

alarm panel

Note: RS232 cabling must not exceed 30 meters

PIN Inputs interface to

Maximum input voltage range 0V to +24V

alarm panel

Input 'low' (alarm) threshold < 1V

Input 'high' (restore) threshold > 2V

Internal pull-up impedance 10K to 3 . 3 V supply

220

240

UTP 10/100 Base T with auto-negotiation

RJ45 socket for CAT5 cabling

Dynamic (DHCP) or fixed

Loss of Ethernet synchronisation

–

Penta band LTE (4G)

–

800/900/1800 MHz

–

2100/2600 MHz

–

Dual band UMTS (3G)

–

900/2100 MHz

–

Dual band GSM (2G)

–

900/1800 MHz

–

SMA socket for antenna

–

Loss of registration with network

Note:

Cabling must not

exceed 3 meters

transmission paths

200

Fault reporting to the alarm panel .

If the dialler is unable to poll to the monitoring centre it reports this

to the alarm panel using a method dependent on the panel interface

mechanism: Dial capture: The line voltage is dropped to simulate

loss of a PSTN connection . Serial: Either regular polls to the interface

are ignored or an explicit message is sent to the panel, depending on

the serial protocol in use . Pin inputs: A relay output can be set open

to indicate fault .

Alarm protocols

SIA (level 1 to 3) reference SIA DC-03-1990 . 0 1(R2003 . 1 0),

Contact ID reference SIA DC-05-1999 . 0 9, Fast format (Scancom),

Robofon (Dial capture only), Telim (Dial capture only),

CESA (Dial capture only)

Tamper detection reporting to

Dial capture interface, Lid & back tamper, Serial Interface, Pin inputs

Monitoring Centre

Fault reporting to Monitoring Centre Transmission interface/path fault

The IRIS dialler constantly 'polls' the monitoring centre to report it is

operational and to report any interface or transmission faults it has

identified . If the dialler has more than one transmission path then all

paths are monitored and faults are reported by an operational path .

If all paths or the dialler fail this is identified by the loss of polls .

This allows the monitoring centre to monitor and calculate the

dialler's availability .

Substitution protection and

All transmissions are authenticated and encrypted using a unique

information security

256 bit security key . This key is automatically updated every day .

Relay outputs

Maximum operating voltage

24V DC

Maximum current rating

100mA DC

Power supply

Supply voltage

9V to 28V DC

Typical current

124mA @ 12V DC

Maximum current

1A @ 12V DC

Recommended external PSU

Note: For Radio Equipment Directive the power cable needs to be

no longer than 3 meters in length

Environmental

Operating temperature range

-10°C to 55°C

Operating humidity range

95% max ., non-condensing

Weights and dimensions

Physical dimensions

19 cm x 13 cm x 4 cm

PCB weight

550 grams

Fully packaged weight

750 grams

220

240

138mA @ 12V DC

140mA @ 12V DC

12V DC 1A 12 Watt