Duro Dyne 27180 Panduan Pemilik - Halaman 2

Jelajahi secara online atau unduh pdf Panduan Pemilik untuk Sistem Pengelasan Duro Dyne 27180. Duro Dyne 27180 8 halaman. Pinspotter

Halaman Cetak

ELECTRICAL REQUIREMENTS

Connect the MF70 to a 60 amp power supply. (208-

230 volts – 60 cycle). The MF70 uses 208 – 230

volt single phase. To wire to 208-230 volt single

phase, the green lead is ground and the white and

black leads are power. It is suggested that the unit

be permanently wired into a 60 amp disconnect box

fitted with 60 amp circuit protection.

MF70 AS A BENCH TOOL

To use your work bench as a welding table, set the

MF70 alongside or on top of the work bench. Cover

the bench top with a copper sheet (.025 inch) which

will act as a permanent ground when the duct work

is placed on the table top. Attach the MF70 ground

clamp to the duct work or copper bench top. The Clip

Pins will quickly weld every time with no burn marks

or wasted pins due to misfires.

BRING MF70 TO THE WORK

Where duct is too large to put on a bench, snap the

ground clamp onto the duct and secure the insulation

quickly by welding the Clip Pins inside or outside of

the ducts as required

SERVICE

The MF70 has been designed and built to withstand

rugged shop usage. The Indicator lights on the front

panel will help you to diagnose minor problems. If your

MF70 fails to operate follow this simple procedure to

find the defective component.

1. Pull the trigger and watch the lights. The green

light (24 volts) and then the red light (220 volts)

should flash on and off.

2. If only the green light comes on, go to step 4.

3. If neither light comes on, press the WELD CYCLE

TEST switch on the front panel.

A. If both lights flash and the transformers do not

hum go to step 5.

B. If both lights flash and the transformers hum,

the problem is either a bad trigger switch or

bad switch cable.

C. If only the green light flashes, go to step 4

D. If neither light flashes, replace 24 volt trans-

former.

4. Replace the weld activator.

5. The problem is probably a bad weld transformer.

Call technical service for further assistance.

(1-800-899-3876)

TIMER ADJUSTMENT

The timer dial facing you on the front panel of the

unit, determines the duration of the weld cycle. For

maximum efficiency of the unit, the weld cycle should

be set for the shortest length of time necessary to

provide a good weld. An excessive amount of time does

not improve the weld. On the contrary, the resulting

weld may not be an acceptable one. It is recommended

that at the start of a production run, using a given

length of pin with a given gauge of metal, the opera-

tor take a few moments to determine the minimum

timer setting to perform the job and leave the timer

at that point.

NOTE: There is a common misconception that the

longer the weld time, the stronger the weld. This is

not true. It is important that you follow the above

instructions for maintaining the minimum weld time.

MAINTENANCE

The MF70 has been designed and built to withstand

rugged shop usage. Constant, trouble-free operation

is assured with a minimum of maintenance. The GUN

TIP , the GROUND CLAMP and all CABLE CONNECTIONS

should be kept clean to maintain a good electrical

contact. Wire brush the parts to remove any oxida-

tion or adhesive that may have accumulated during

the fastening operation.

INSTALLING CLIP PINS

Clip Pins are welded as easily as "A", "B", "C".

"A"

Position the Clip pin on the

Magnetic tip of hand gun.

"B"

Press down through the insu-

lation, twist the gun, and pull

the trigger. Do not release

the trigger until the timer

cycle has ended.

"C"

The Clip Pins are

permanently welded

in position flush with

the insulation.