Elsner WS1 Style-4 PF Instruksi Singkat

Jelajahi secara online atau unduh pdf Instruksi Singkat untuk Sistem Kontrol Elsner WS1 Style-4 PF. Elsner WS1 Style-4 PF 2 halaman.

Halaman Cetak

Brief Instruction

Mounting of WS1 Style

Item numbers 60180-60189 (WS1 Style), 60194 (WS1 Style-4 PF)

The manual with additional information about commissioning,

functions and use of the controls WS1 Style can be download-

ed from www.elsner-elektronik.de in the menu area "Service/

Downloads".

Warning, mains voltage! National legal regulations are to be

observed. Installation, inspection, commissioning and

troubleshooting of the device must only be carried out by a

competent electrician.

Notes on wireless equipment

When planning facilities with devices that communicate via radio, adequate radio

reception must be guaranteed. The range will be limited by legal regulation and

structural circumstances. Avoid sources of interference and obstacles between re-

ceiver and transmitter, that could disturb the wireless communication. Those

would be for example:

•

Walls and ceilings (especially concrete and solar protection glazing).

•

Metal surfaces next to the wireless participants (e. g. aluminium

construction of a conservatory).

•

Other wireless devices and powerful local transmitters (e.g. wireless

headphones), which transmit on the same frequency. Please maintain a

minimum distance of 30 cm between wireless transmitters for that reason.

Preparing the installation location

The device must only be installed and used in dry, interior

spaces. Avoid condensation.

The device is to be installed flush to the wall surface. When selecting an installation

location, please ensure that the measurement results of the integrated temperatu-

re/humidity sensor are affected as little as possible by external influences. Possible

sources of interference include:

•

Direct sunlight

•

Drafts from windows and doors

•

Draft from ducts which lead from other rooms to the concealed box

•

Warming or cooling of the building structure on which the device is

mounted, e.g. due to sunlight, heating or cold water pipes

•

Connection lines which lead from warmer or colder areas to the device

Cut-out dimensions for concealed box:

W = 166 mm +1 -0 | H = 116 mm +1 -0 | D = 80 mm

An external antenna can be connected in order to improve wireless communicati-

ons. During installation, a conduit 50 cm in length should be placed beneath the

recessed housing, in which the external antenna can be mounted (antenna dimen-

sions approx. 565 x 8 x 5, L × W × H in mm):

Conduit angled diagonally dow-

Conduit angled vertically downwards (only

nwards (for cable access from

for cable access from above!)

above or below)

concealed

box

cable

45°

M16 conduit, 50 cm in length

Preparing for installation

The display unit is held by magnets. Re-

move the front part from the concealed

box.

Caution: The display is connected

with a flat-ribbon cable to the circuit

board in the concealed box.

Wall-fitting

Cavity wall fitting

Assembling the control unit with concealed box

During electrical installation, please introduce all connection cables into the con-

cealed box through the lower or upper side wall. In the process, keep the individual

connection wires short to prevent long reserve loops.

After connecting the cables screw the security covering onto the concealed box.

cable

The security covering must be fixed before the control is put

into operation! It prevents contact with current-carrying parts

in the concealed box.

M16 conduit,

50 cm in length

By adjusting the mounting screws, the display unit will rest flat on the wall later

and be held by the magnets safely.

Connect the flat ribbon cable to the display and place the display unit on the con-

cealed box. The magnets must be attracted by the mounting screws considerably

and the display unit must rest tightly on the concealed box.

Mounting of WS1 Style • Version: 30.06.2020 • Technical changes and errors excepted. • Elsner Elektronik GmbH • Sohlengrund 16 • 75395 Ostelsheim • Germany • www.elsner-elektronik.de • Technical Service: +49 (0) 7033 / 30945-250

Mounting of WS1 Style

Loosen the plug so that the display unit

can be removed.

Remove all parts of the transportation

lock/packing.

The security covering in the concealed

box is attached with four screws: Loosen

the screws and take off the security cover-

ing.

Remove the circuit board from the con-

cealed box to be installed a keep it in a

place where it is protected from dirt. It

may never be exposed to dust or mo-

isture!

Place the concealed box in the wall so

that the arrows point upwards.

For fitting, screw the cover (board) on to

the concealed box with the enclosed

screws.

Clamp the concealed box to the wall with

the four enclosed screws.

Upon delivery, the pouch containing the

assembly screws can be found in the con-

trol unit's concealed box.

Adjust the screws of the magnetic moun-

ting with the enclosed template. Each of

the four screws must be adjusted individi-

ally in height.

When the edge of the template rests on

the wall surface (1), the template must

rest on the mounting screws as well (2).

Structure of the connector board WS1 Style

1 Mains connection

12 Wall button 4

L/N/PE 230 V/50 Hz

(10:+12V|11:Up|12:Down)

2 Drive group 1

13 Weather station (terminals 1-2)

3 Drive group 2

Wire assignment: red = 1, black = 2,

4 Drive group 3

yellow and white = not connected

5 Drive group 4

14*Multifunctional input 1

6 Outer conductor L1

(terminal 3: +12 V | 4: GND | 5: IN)

7 Multifunctional output 1

15*MF input 2 (6: +12 V | 7: GND | 8: IN)

(potential-free)

16 Connector for flat-ribbon cable to

8 MF output 2 (potential-free)

front board

9 Wall button 1

17 Microfuse T6,3 A

(terminal 1: +12 V | 2: Up | 3: Down)

10 Wall button 2

* Supply voltage e. g. indoor sensor

(4: +12 V | 5: Up | 6: Down)

possible via MF inputs

11 Wall button 3

(No. 14, terminal 3(+), 4(-) and

(7: +12 V | 8: Up | 9: Down)

No. 15, terminal 6(+), 7(-)),

max. 50 mA altogether.

Structure of the connector board WS1 Style-PF