Cayken SCY-1300 Panduan Pengoperasian - Halaman 8

Jelajahi secara online atau unduh pdf Panduan Pengoperasian untuk Bor Cayken SCY-1300. Cayken SCY-1300 10 halaman.

Halaman Cetak

Attention: Our company does not assume any responsibility because the machine is not solid

or fixed safety facilities are not in appropriate place cause accident.

ELECTRICAL SAFETY

Tool before connecting power, using the socket must be able to fit the plug machine. The

380 model to determine the fire and. ine the correct docking, power supply socket with the

need of professionals to complete. o not arbitrarily change the plug, adapter plugs can t pick.

The electric tool wire used together.

SAFETY INSTRUCTIONS

1 lease read this manual carefully before using the magnetic drilling characteristics and rules

of operation the operator must go through specialized training fully understand before

operating the machine The machine can not be in the dust flammable explosi e gas wor

king under the dangerous en ironment workplace should ha e good lighting conditions

kept clean and in an orderly

2 lease confirm the oltage olts before use high working oltage exceeds the rated oltage

of the 5

such as o er will cause the motor burned or leakage accident resulting in pers

onal in ury

3 perating personnel must be absorbed in the work not only to keep a clear mind and more

rational operation Tired drinking or taking drugs stimulants drug do not operate the ma

chine when using power tools as long as a little distraction may occur for the serious cons

equences of accidents

4 To wear appropriate clothing operating the machine

clothes wear ewelry

ustn t let the hair clothes glo es contact rotating parts on the ma

chine oose clothing or ewelry long hair easy to tangle accident

5 on t use electric tools must ha e the machine stored in children can not get on t let un

familiar with machine operation method and don t read the manual people use the machine

6 on t let internal motor with water entilation hole can not be blocked when operating the

machine so as to a oid motor leakage or because of poor heat burned

7 perating the machine please confirm the drilling position whether there is danger such as

power lines gas pipelines water pipe etc

8 The magnetic drill with a safety rope work on the walls and ceiling must fasten safety rope

at the same time the use of spray cooling tool

the corresponding protecti e measures

9 The magnetic base drill should be started in idle state prohibit starting with load so as not

to damage the magnetic base drill high altitude operations please note that the magnetic

fixed firmly to pre ent the magnetic base drill down

AYKEN

PROFESSIONAL DRILLING

hen you work mustn t be too loose

nd to drill down to the iron scurf should take

www.cayken.com.cn

AYKEN

PROFESSIONAL DRILLING

10 ower line should be rubber cable used in line with national standards at the same time

the machine should be connected to the power leakage protection switch and guarantee

grounding reliable grounding

11 Installation or mobile machine must switch off the machine and then cut off the machine

power supply mobile magnetic base drill he should raise the magnetic base drill can not

drag on the operating surface damage to the antimagnetic seat or the workpiece surface

12 ot to cut off the power line or replace the plug so as to a oid the occurrence of circuit board

burned or magnetic seat burn

13 fter the machine in a cumulati e 300 hours of work should check whether you need to

replace the brush after 3 months of use to the machine safety inspection in maintenance

must use the original parts in order to enable the machine to achie e the best state at the

same time all about machine maintenance and inspection shall be conducted by professional

personnel to complete

arning using non factory original accessories easy to cause the tool damage e en pers-

onal in ury

MAGNETIC HOLLOW DRILL INSTRUCTIONS

1 . lug the power plug the drill bit aim at processing position make the magnetic switch is

opened so that the magnetic is adsorbed on the surface of steel plate magnetic materials

o impurities on the surface and check whether the attracti e force is normal or not ge-

neral plate thickness should be more than 10mm

2 . lease placed the magnetic base drill required from the drilling near site and select the appro

priate adsorption material nd will handle hole safety rope penetrates into the frame the

other one is in fastening frame after the penetration of the buckle and then close the safety

rope buckle

3 . or a support screw regulating the support screw that the bottom touches the workpiece

surface

4. or the magnetic base is pro ided with the angle of the drill the use of angle wrench mo em-

ent angle disk in the annex to the belt rack makes bit central alignment processing position

tighten the angle wrench

5 . pen the electric drill switch check whether the drill bit beat sound is normal if e erything is

normal can turn the handle to feed

6. tart feeding should be slow gi es the quantity of about 0 05mm r in general not too much

force to pre ent o erload

7. If the drill for kill suddenly stopped you must turn off the power switch immediately

close the magnetic control switch

8 lease shut down for a period of time machine in continuous use for 2 3 hours in case mag-

netic base is o erheated and leakage or burned

www.cayken.com.cn

)

and and pull off should not loose and mobile

)

. (

, (

ust