Datalogic S5N-MH Series Buku Petunjuk

Jelajahi secara online atau unduh pdf Buku Petunjuk untuk Pembaca kode batang Datalogic S5N-MH Series. Datalogic S5N-MH Series 5 halaman.

Halaman Cetak

This product is covered by one or m ore of the following patents.

European Patent 851,211 B1; 1,111,690 B1; 1,148,346 B1; 1,209,487 B1.

Italian Patent IT 1,321,772.

S5N-PH/MH SERIES

INSTRUCTION MANUAL

CLASS 1 IEC 60825-1 (2014)

LASER PRODUCT

IEC 60825-1 "Caution – use of controls or adjustments or performance of

procedures other than those specified herein may result in hazardous

radiation exposure"

CONTROLS

OUTPUT LED (S5N-PH/MH...B01/C01/F01)

The yellow LED ON indicates that the N.O. (normally open) output status

is closed.

POW ER ON LED

The green LED indicates that the sensor is operating.

TRIMMER (S5N-PH/MH...B01/C01/F01)

The trimmer can be used to adjust sensitivity; the operating distance

increases turning the trimmer clockwise.

W ARNING: The trim m er rotation is lim ited to 270° by a m echanical stop.

Do not apply excessive torque when adjusting (m ax 40 Nm m ).

INSTALLATION

S5N-PH: The sensor can be fixed by means of the M18x1 threaded body

through a  18 mm hole, using the specific washer and the two CH.24

nuts enclosed (1.5 Nm maximum tightening torque).

Amongst the various possible solutions, we suggest to choose the

combination that offers the best visibility of the signalling LEDs and the

easiest access to the trimmer.

22 mm nuts, h=8 mm, (2 Nm maximum tightening torque) are available to

guarantee an improved torque.

S5N-MH: The sensor can be fixed by means of the M18x1 threaded body

through a  18 mm hole, using the two CH.24 nuts enclosed (22 Nm

maximum tightening torque).

Various orientable fixing brackets for both plastic and metallic versions

are available to ease sensor positioning (please refer to the accessories

listed in the general catalogue).

The operating distance is measured from the front surface of the sensor

lens.

The connections are compliant to the EN 60947-5-2 standard.

S5N-PH/MH...B01/C01/F01

BROWN

10 ... 30 Vdc

WHITE

N.C. OUTPUT

BLACK

N.O. OUTPUT

BLUE

0 V

S50-PH VERSION

S5N-PH VERSION

with

trimmer

14.5

1.5

3.5

CABLE VERS.

14.5

TRIMMER

N°.2 Ø3.8

POWER ON LED

OUTPUT LED

TECHNICAL DATA

S5N-PH PLASTIC VERSIONS

Power supply:

Ripple:

Current consumption

(output current excluded):

Outputs:

Output current:

Output saturation voltage:

Response time:

Switching frequency:

Indicators:

Setting:

Operating mode:

DARK mode on N.O. output / LIGHT mode on N.C. output (mod.B01/F01)

Operating temperature:

Storage temperature:

Insulating strength:

Insulating resistance:

Operating distance (typical values):

Emission type:

Max. power  1 mW; Pulse = 5  s;  = 645...660 nm; Frequency  25 kHz

Ambient light rejection:

0.5 mm amplitude, 10 ... 55 Hz frequency, for every axis (EN60068-2-6)

Vibrations:

Shock resistance:

Housing material:

Lens material:

Mechanical protection:

Connections:

Weight:

75 g. max. cable vers. /25 g. max. conn. vers.

CONNECTIONS

S5N-PH/MH...G00

M12 CONNECTOR

10 ... 30 Vdc

TEST +

NOT USED

0 V

DIMENSIONS

M O D E L S

S50-MH VERSION

S5N-MH VERSION

without

trimmer

14.5

TRIMMER

POWER ON LED

OUTPUT LED

S5N-MH METAL VERSIONS

10 ... 30 Vdc limit values

2 Vpp max.

35 mA max. (mod.B01/C01/F01)

30 mA max (mod.G00)

N.O. and N.C.; PNP or NPN (short-circuit protection)

100 mA max.

2 V max.

333  s

1.5 kHz

OUT PUT LED (YELLOW) (mod.B01/C01/F01)

POWER ON LED (GREEN)

sensitivity trimmer (mod.B01/C01/F01)

LIGHT mode on N.O. output / DARK mode on N.C. output (mod.C01)

-10 ... 50 °C

-25 ... 70 °C

500 Vac 1 min., between electronics and housing

>20 M 500 Vdc, between electronics and housing

B01: 0.1...9 m on R2 reflector

C01: 0...25 cm

F01/G00: 0...50 m

RED LASER: Class 1 IEC 60825-1 (2014) (mod.B01/C01/G00)

Class 1 CDRH 21 CFR PART 1040.10 (mod.B01/C01/G00)

According to EN 60947-5-2

11 ms (30 G) 6 shock for every axis (EN60068-2-27)

PBT

Nickel-plated brass

PMMA

IP67 Metal versions type 1 enclosure

2 m cable  4 mm / M12 - 4 pole connector

110 g. max. cable vers. /60 g. max. conn. vers.

SETTING

Setting of S5N-PH/MH...B01

Position the sensor and reflector on opposite sides.

Turn the sensitivity trimmer to the maximum position.

Moving the sensor both vertically and horizontally, determine the power

ON and OFF points of the OUTPUT LED and then mount the sensor in

the middle of the points defined.

If necessary reduce sensitivity in order to detect very small targets.

In order to improve alignment, repeat the given procedure whilst

progressively reducing the sensitivity.

Setting of S5N-PH/MH...F01/G00

Position the sensor and reflector on opposite sides.

Turn the sensitivity trimmer to maximum: moving the sensor both

vertically and horizontally, determine the power ON and OFF points of the

OUTPUT LED and then mount the sensor in the middle of the points

defined.

If necessary, reduce sensitivity using the trimmer, in order to detect very

M O D E L S

with

without

small targets. In order to improve alignment, repeat the procedure

trimmer

detailed above whilst progressively reducing the sensitivity.

Setting of S5N-PH/MH...C01

Turn the sensitivity trimmer to minimum: the OUTPUT

LED is OFF.

Position the target to detect in front of the sensor.

Turn the sensitivity trimmer clockwise until the

OUTPUT LED turns ON (Target detected state, pos.A).

CABLE VERS.

Remove the target, the OUTPUT LED turns OFF.

Turn the sensitivity trimmer clockwise until the OUTPUT LED turns ON

(Background detected state, pos.B).

The trimmer reaches maximum if the background is not detected.

Turn the trimmer to the intermediate position C, between the two

POWER ON LED

positions A and B.

OUTPUT LED

TEST FUNCTION (S5N-PH/MH...G00)

The TEST+ input can be used to deactivate the emitter and verify that the

system is operating correctly.

The receiver output should switch when the test is activated while the

beam is uninterrupted.

The input activating voltage range is 10...30 Vdc.

Datalogic S.r.l.

Via S. Vitalino 13 - 40012 Calderara di Reno - Italy

Tel: +39 051 3147011 - Fax: +39 051 3147205 - www.datalogic.com

Helpful links at www.datalogic.com: Contact Us, Terms and

Conditions, Support.

The warranty period for this product is 36 months. See General Terms

and Conditions of Sales for further details.

For information about the disposal of Waste Electrical

and Electronic Equipment (WEEE), please refer to the

website at www.datalogic.com.

RESERVED.  Without limiting the rights under copyright, no part of

this documentation may be reproduced, stored in or introduced into a

retrieval system, or transmitted in any form or by any means, or for any

purpose, without the express written permission of Datalogic S.p.A.

and/or its affiliates. Datalogic and the Datalogic logo are registered

trademarks of Datalogic S.p.A. in many countries, including the U.S.A.

and the E.U. All other trademarks and brands are property of their

respective owners. Datalogic reserves the right to make modifications

and improvements without prior notification.

826000422 Rev.C

MAX

MIN