Dux Centreflush2 Cistern Petunjuk Instalasi

Jelajahi secara online atau unduh pdf Petunjuk Instalasi untuk Produk Pipa Dux Centreflush2 Cistern. Dux Centreflush2 Cistern 2 halaman.

Halaman Cetak

INSTALLING

1. Take the lid off the cistern leaving the protective film in intact, it is preferable to leave this intact until any paint work

is completed.

2. Fit the Flushpipe to the back of the pan and if necessary cut the short leg of the flushpipe so that when fitted to the

pan it is 80mm from the wall to the centreline of the flushpipe.

3. Fit the reducing bush supplied to the top of the flushpipe and then sit the cistern onto the bush. Making sure that the

horizontal leg of the flushpipe is horizontal. Measure the distance from the top of the cistern to the required height line

as established in step 2 (Setting out). This measurement is the amount to cut off the long leg of the flushpipe. Remove

the cistern and flushpipe from the pan and cut the flushpipe accordingly.

4. Drill and fit the four mounting screws to the wall at the position established in step 3 (Setting out) leaving the screw

protruding from the wall approximately 10mm.

5. Re-assemble the flushpipe onto the pan with the reducer bush and the flushpipe nut then lower the cistern onto

flushpipe and the four mounting screws.

6. Tighten the four mounting screws and Flushpipe nut.

7. Flush any dirty water out of the water supply to prevent dirt and debris from clogging the valves.

8. Install the inlet valve, turn on the water supply and adjust the water level to the required flushing volume.

Installation and adjustment guidelines are on the back of this page.

9. Fit the cistern lid and check the operation of both the full and half flush modes.

Note: If fitting the cistern to hardboard or gib board and there is no backing timber we suggest the use of "Toggles"

which are readily available from hardware stores.

Typical Layout for Dux Centreflush2 Cistern

Valve Installation and Service

Inlet Valve Installation and Service

Installation & Adjustment

The inlet valve can be fit to either the left or right side of the cistern.

Once fitted you will need to turn the water supply on and adjust the float up

or down until you have the desired full flush volume.

4.5 L, 6 L or 9 L as marked on the inside edge of the cistern. To adjust the

Adjustment

water level, turn the adjustment screw on the side of the valve.

Diaphragm

Screw

nut

Service & Cleaning

It is possible that small debris can prevent the valve shutting off.

To remedy this, the diaphragm can be cleaned as follows,

Outlet Valve Removal

To remove the outlet valve turn the valve

clockwise to unlock then lift.

Half Flush Adjustment

To adjust the half flush volume remove the valve and

slide the float up or down.

Sliding float up decreases volume

Sliding float down increases volume

Flushing Volume Valve Settings

FLUSHING VOLUME

WATERLINE

9/4.5 Litre

9 L

6/3 Litre

6 L

4.5/3 Litre

4.5 L

1. Unclip the adjustment screw from the float arm

2. Rotate the diaphragm nut anti-clockwise and remove the

diaphragm.

3. Rinse valve and diaphragm under running water to remove any

debris.

4. Re-assemble in reverse order

Push Button Adjustment

The button rods can be adjusted by screwing up or down

the rod. After adjustment there should be 1 -2mm gap

between the button rod and valve.

Full Flush Adjustment

To adjust the full flush volume remove the valve and

slide the adjuster up or down.

Sliding adjuster up decreases volume

Sliding adjuster down increases volume

HALF FLUSH SETTING

FULL FLUSH SETTING