DV Mark EVO 1 Panduan Pemilik - Halaman 7
Jelajahi secara online atau unduh pdf Panduan Pemilik untuk Penguat Alat Musik DV Mark EVO 1. DV Mark EVO 1 9 halaman.
Halaman Cetak
EVO1 CONTROLLER
The optional EVO 1 CONTROLLER allows to switch between CH1 / CH2 and turn ON/OFF the FX1, FX2 and BOOST, plus accessing
the TUNER with MUTE function pressing and holding the boost switch.
The EVO 1 MIDI port features 9VDC phantom power (200 mA) via MIDI 5 poles cable (all pins connected) to power the EVO
CONTROLLER (or MIDI Pedalboard compatible with this voltage/power).
The EVO 1 can be controlled also via programmable MIDI pedalboard as for the MIDI commands listed below:
•
TRX MIDI CHANNEL #0
•
CH1 Program Change #1
•
CH2 Program Change #2
•
FX1 Control Change #1 (ON 1 / OFF 0)
•
FX2 Control Change #2 (ON 1 / OFF 0)
•
BOOST Control Change #3 (ON 1 / OFF 0)
•
TUNER Control Change #28 (ON 1 / OFF 0)
The DV Mark EVO Control software is available for FREE DOWNLOAD at www.dvmark.it (for Windows and MAC) and it allows to
customize your DV Mark EVO 1 selecting the preferred AMP on each of the six locations of the two channels and the preferred type of
reverb (or none) for each channel and its parameters, plus virtual CAB/Speaker Emulator choices (assignable to the XLR Line Out).
- DOWNLOAD the DV Mark EVO Control software and unzip the file, then install the version compatible with your computer.
- Connect the USB port on the rear panel of the DV Mark EVO 1 to a computer using a USB A/B (printer) cable, when the unit is
communicating with the software the connection LED on the left bottom side will turn from grey into green.
- To select an AMP in one of the 6 positions of CH1 click on the arrows on its right side and the list of AMPS will be shown, select
the desired one clicking on its name, then press STORE; same procedure for CH2.
- To select the reverb type for CH1 click on the arrows on EFFECT section and select the desired one clicking on its name, set the
parameters as for your preference and press STORE; same procedure for CH2.
CH1
CH2
EVO1
CONTROLLER
FX1
FX2
BOOST
HOLD FOR
MUTE
-
TUNER
DV MARK CONTROL SW
The DV Mark EVO Control software is available for FREE DOWNLOAD at www.dvmark.it (for Windows and MAC) and it allows to
customize your DV Mark EVO 1 selecting the preferred AMP on each of the six locations of the two channels and the preferred type of
reverb (or none) for each channel and its parameters, plus virtual CAB/Speaker Emulator choices (assignable to the XLR Line Out).
- DOWNLOAD the DV Mark EVO Control software and unzip the file, then install the version compatible with your computer.
- Connect the USB port on the rear panel of the DV Mark EVO 1 to a computer using a USB A/B (printer) cable, when the unit is
communicating with the software the connection LED on the left bottom side will turn from grey into green.
- To select an AMP in one of the 6 positions of CH1 click on the arrows on its right side and the list of AMPS will be shown, select
the desired one clicking on its name, then press STORE; same procedure for CH2.
- To select the reverb type for CH1 click on the arrows on EFFECT section and select the desired one clicking on its name, set the
parameters as for your preference and press STORE; same procedure for CH2.
- To select virtual CAB/Speaker Emulator to assign to the XLR Line Out, click on the arrows on CABINET section and select the desired
one clicking on its name and press STORE.
- The FIRMWARE button on the right bottom side allows to upgrade the EVO1 amplifier firmware when new updates are released.
7