Datasensor S62-M1 Series Buku Petunjuk - Halaman 3

Jelajahi secara online atau unduh pdf Buku Petunjuk untuk Aksesori Datasensor S62-M1 Series. Datasensor S62-M1 Series 4 halaman.

Halaman Cetak

S62-PL...B Laser

Polarised retroreflex

INSTRUCTION MANUAL

CONTROLS

OUTPUT LED (yellow)

The yellow LED ON indicates the following output status: N.O.

closed and N.C. open.

POWER ON LED (green)

The green LED ON indicates the sensor powering status and

laser emission presence.

SENSITIVITY TRIMMER (ADJ.)

Monoturn trimmer that adjusts the sensitivity and thus the

sensor operating distance.

Please refer to "SETTING" paragraph for the correct use

procedure.

WARNING: the maximum mechanical trimmer rotation is

equal to 240°. Do not apply excessive torque over the

maximum and minimum positions.

INSTALLATION

The sensor can be positioned by

means of the three housing's

holes using two screws (M4x25

or longer, 1.5 Nm maximum

tightening torque) with washers.

Various orientable fixing brackets

to ease the sensor positioning

are available (please refer to the accessories listed in the

general catalogue).The operating distance is measured from

the front surface of the sensor optics.

The M12 connector can be oriented at two different positions

using the specific fastening spring and rotating the block to

180°.

CONNESSIONS

M12 connector

TECHNICAL DATA

Power supply:

Ripple:

Consumption

(output current excluded):

Outputs:

PNP or NPN N.O. / N.C.; 30 Vdc max. (short-circuit protection)

Output current:

Output saturation voltage:

Response time:

Switching frequency:

Emission type:

RED LASER (λ = 645...665 nm): Class 2 EN 60825-1 (1994), Class II CDRH 21

Operating distance (typical values):

Min. detectable object dimension:

Indicators:

Setting:

Functioning temperature:

Storage temperature:

Dielectric strength:

Insulating resistance:

Ambient light rejection:

Vibrations:

0.5 mm amplitude, 10 ... 55 Hz frequency, for every axis (EN60068-2-6)

Shock resistance:

Housing material:

Lens material:

Mechanical protection:

Connections:

Weight:

Alignment:

- Position the sensor and reflector aligned on opposite sides at the

desired distance.

- Turn

maximum

the

sensitivity adjustment

(clockwise).

- Determine the powering on and powering off points of the yellow LED

(OUT) by moving vertically and horizontally the sensor and mount the

sensor in the middle of the points found.

Control:

- Enter laterally the object inside the

operating field and control that the

yellow LED turns on.

- Remove the object and check that

the yellow LED turns off immediately

PERFORMANCES

TAB.1: Operating distances (m)

REFLECTOR

R7 /R20

0.3 ... 16

0.3 ... 20

0.4 ... 22

0.3 ... 22

Note: The use of the RT 3970 reflecting tape is not suggested.

10 ... 30 Vcc

2 Vpp max.

30 mA max

100 mA max (overload and overvoltage protection)

≤ 2 V

200 µs

2.5 kHz

CFR PART 1040.10

Pulsed emission: pot. max ≤ 5 mW; pulse duration = 5 µs;

frequency max = 32 KHz

refer to TAB.1

0.5 mm at 0.5m (minimum spot)

OUTPUT LED (YELLOW) / POWER ON LED (GREEN)

Monoturn sensitivity adjustment trimmer

-10 ... 55 °C

-20 ... 70 °C

500 Vac 1 min., between electronics and housing

>20 MΩ 500 Vdc, between electronics and housing

according to EN 60947-5-2

11 ms (30 G) 6 shock for every axis (EN60068-2-27)

ABS

PMMA window, polycarbonate lenses

IP67

M12 4-pole connector

40 g. max.

SETTING

trimmer

(ADJ.)

spot diameter (mm)

0.2 ... 2

distance (mm)

DIMENSIONS

4.7

RECEIVER

EMITTER

M12

Ø15

SENSITIVITY TRIMMER

6.18

10.7

POWER ON LED

OUTPUT LED

SAFETY PRECAUTIONS

All the electric and mechanical

safety regulations have to be

respected

during

sensor

functioning.

The sensor has to be protected

against mechanical damage.

Apply the labels supplied in a

visible position near the laser emission beam.

Do not stare directly into the laser beam!

Do not point the laser beam towards people!

Eye irradiation superior to 0.25 seconds is dangerous.

Please refer to the Class 2 Standard (EN60825-1).

These sensors can not be used for safety applications!

EX-II-3D T6

T6 (<85°C)

Temperature class:

Max. Power consumption: 800 mW at 30 Vdc

Max. Internal capacitance: 100 nF

Internal inductance:

negligible

DECLARATION OF CONFORMITY

We DATASENSOR S.p.A. declare under our sole responsibility that

these products are conform to the 2004/108/CE, 2006/95/CE Directives

and successive amendments.

WARRANTY

DATASENSOR S.p.A. warrants its products to be free from defects.

DATASENSOR S.p.A. will repair or replace, free of charge, any product

found to be defective during the warranty period of 36 months from the

manufacturing date.

This warranty does not cover damage or liability deriving from the

improper application of DATASENSOR products.

DATASENSOR S.p.A. Via Lavino 265

40050 Monte S. Pietro - Bologna - Italy

Tel: +39 051 6765611

Fax: +39 051 6759324

http://www.datasensor.com

e-mail: [email protected]

DATASENSOR S.p.A. cares for the environment: 100% recycled

paper.

DATASENSOR S.p.A. reserves the right to make modifications

and improvements without prior notification.

826003251 Rev.B