Datavan Wonder Series Panduan Instalasi Cepat - Halaman 2

Jelajahi secara online atau unduh pdf Panduan Instalasi Cepat untuk Terminal sentuh Datavan Wonder Series. Datavan Wonder Series 2 halaman.

Halaman Cetak

Installing the Power Cord, Power Adapter, and

Network Cable

1. Place the Touch Terminal on a soft and ﬂat surface, with the LCD panel facing

down. Remove the cable compartment cover. (a)

2. Connect the network cable to the LAN port. Then connect the power adapter to the

DC IN jack. (b)

3. Route the power adapter and the network cable through the cable compartment. (c)

4. Align and install the cable compartment. (d)

5. Connect the power adapter to the power cord. Then plug the other end of the

power cord to an electrical outlet. (e)

6. Connect the network cable to a hub or switch. (f)

When removing the power adapter, be sure to hold the

end of power adapter ﬁrmly and pull it out.

Installing the Identification Reader (Optional)

1. Remove the identiﬁcation reader

compartment cover. (a)

2. Firmly connect the identiﬁcation

reader connector into the slot inside

the compartment. (b)

3. Align and install the identiﬁcation

reader onto its compartment. (c)

4. Secure the identiﬁcation reader to

the Touch Terminal using the two

screws. (d)

Installing the VESA Mount (Optional)

1. Place the Touch Terminal on a soft and ﬂat

surface, with the LCD panel facing down.

Remove the cable compartment cover. (a)

2. Remove the four screws on the stand. (b)

3. Remove the stand. (c)

4. Align and install the mount bracket on the back

of the Touch Terminal. (d)

5. Secure the mount bracket to the Touch Termi-

nal with the four screws. (e)

6. Drill four small holes on the mounting location

and insert the plastic washers into the holes. (f)

7. Align by the screw holes and then install the

wall bracket on the wall. (g)

8. Secure the wall bracket to the wall with the four

supplied screws. (h)

9. Align and hook the Touch Terminal to the wall

bracket, and then push down to secure it into

place. (i)

10. Replace the cable compartment cover for

storing the stand assembly. (a)

Installing the Customer Display (Optional)

1. Place the Touch Terminal on a soft and ﬂat surface, with the LCD panel facing down.

Remove the cable compartment cover. (a)

2. Remove the four screws on the stand. (b)

3. Remove the stand. (C)

4. Remove the supportive tape from the stand. (d)

5. Remove the four screws on the stand cover. (e)

6. Remove the stand cover. (f)

7. Align and install the customer display into the four threaded standoﬀs on the stand. (g)

8. Secure the customer display to the stand with the four screw nuts. (h)

9. Route the customer display's interface cable through the cable guides on the stand

and through the cable compartment as illustrated. (i)

10. Connect the customer display's interface cable to the RJ-45 COM port on Touch

Terminal. (j)

11. Reverse steps 6 through 1 to complete installing the customer display.

Installing the Secondary LCD Display (Optional)

1. Place the Touch Terminal on a soft and ﬂat surface, with the LCD panel facing down.

Remove the cable compartment cover. (a)

2. Remove the four screws on the stand. (b)

3. Remove the stand. (C)

4. Remove the supportive tape from the stand. (d)

5. Remove the four screws on the stand cover. (e)

6. Remove the stand cover. (f)

7. Align and install the secondary LCD display into the four threaded standoﬀs on the

stand. (g)

8. Secure the secondary LCD display to the stand with the four screw nuts. (h)

9. Route the secondary LCD display's power cable and USB cable through the cable

guides on the stand as illustrated. (i)

10. Connect the secondary LCD display's power cable and USB cable to the corresponding

ports on Touch Terminal. (j)

11. Reverse steps 6 through 1 to complete installing the secondary LCD display.