Frigidaire CFTR1826PS5 Panduan Penggunaan & Perawatan - Halaman 8
Jelajahi secara online atau unduh pdf Panduan Penggunaan & Perawatan untuk Kulkas Frigidaire CFTR1826PS5. Frigidaire CFTR1826PS5 13 halaman.
Halaman Cetak............ ;=======_;_ !i!
_
/ __=====i_
g __,_,_,_,_,_,_,_,_,_,_,_,_,_,_,_,_,_,_,_,_,_,_,_,_,_,_,_,_,_,_
_,,_,_ .................
==============
_ _,,_ _,_ _,_,,_,,_
,,_ii_i_
i
To avoid electric shock, which can cause death or
severe personal injury, disconnect the refrigerator
from electricalpower before connecting a water
supply line to the refrigerator.
• Copperor StainlessSteel braidedtubing is
recommendedfor the water supply line.Water
supply tubing made of 1/4 inch plasticis not
recommendedto be used. Plastic tubing greatly
increasesthe potentialfor water leaks,and the
manufacturer will not be responsiblefor any
damage if plastictubing is used for the supply line.
DO NOT install water supply tubing in areas
where temperatures fall below freezing.
Chemicalsfrom a malfunctioning softener
can damage the ice maker. If the ice maker
is connected to soft water, ensure that the
softener is maintained and working properly.
Ensure that your water supply line connections
comply with all local plumbing codes.
Before Inst_lling The Water Supply Line, You
Will Need:
Basic Tools: adjustable wrench, fiat-blade
TH
screwdriver, and Phillips
screwdriver
Access to a household cold water line with
water pressure between 30 and 100 psi.
1
A water supply line made of /4 inch (6.4
mm) OD, copper or stainless steel tubing.
To determine the length of tubing needed_
measure the distance from the ice maker inlet
valve at the back of the refrigerator to your
cold water pipe. Then add approximately 7 feet
(2.1 meters)_ so the refrigerator can be moved
out for cleaning (as shown).
A shutoff valve to connect the water supply line
to your household water system. DO NOT use
a self-piercing type shutoff valve.
A compression nut and ferrule (sleeve) for
connecting a copper water supply line to the
ice maker inlet valve.
2.
Place end of water
supply line into sink or
bucket. Turn ON water
supply and flush supply
line until water
is clear. Turn OFF water
supply
at shutoff valve.
3.
Remove plastic cap from water valve inlet and
discard
cap.
4.
If you use copper tubing
- Slide brass
compression
nut, then ferrule (sleeve)
onto
water
supply line. Push water
supply line into
water
valve inlet as far as it will go (1/4 inch /
6.4 ram). Slide ferrule
(sleeve)
into valve inlet
and finger tighten
compression
nut onto valve.
Tighten
another
half turn with a wrench;
DO
NOT over tighten.
See Figure 1.
If you use stainless
steel tubing
- The nut and
ferrule
are already
assembled
on the tubing.
Slide compression
nut onto valve inlet and
finger tighten
compression
nut onto valve.
Tighten
another
half turn with a wrench;
DO
NOT over tighten.
See Figure 2.
5.
With steel clamp and screw, secure water
supply
line (copper
tubing
only) to rear panel
of refrigerator
as shown.
6.
Coil excess water supply
line (copper
tubing
only),
about 21/2 turns,
behind refrigerator
as shown and arrange
coils so they do not
vibrate
or wear against any other surface.
7. Turn ON water
supply at shutoff
valve and
tighten
any connections
that leak.
8.
Reconnect
refrigerator
to electrical
power
source.
9.
To turn ice maker on, lower wire signal arm
(side mounted)
or set the ice maker's On/
Off power switch to the "I" position
(rear
mounted).
Water
valve
Checkwith your local building authonty for
recommendationson water linesand assodated
materialsprior to installing your new refrigerator.
Dependingon your local/statebuilding codes,
Frigidairerecommendsfor homes with existing
valves its Smart Choice ® water line kit 5305513409
(with a 6 ft. StainlessSteelWater Line) and
for homes without an existing valve, Frigidaire
recommendsits Smart Choicewater _ line kit
5305510264(with a 20 ft. Copper Water Line with
self-tapping saddle valve). Pleaserefer to www.
fr!g!daire.com/_ore for more information 1 ........................
To Connect Water Supply Line To Ice Maker
Inlet Valve
1. Disconnect refrigerator from electric power
source.
Include
enough
tubing
m Ioo p [o a.ow
moving
refrigerator
out
for
c_eaning,
from
household
water
supply
Figure 1
Figure 2
After connecting the water supply, refer to
"How to Prime the Water Supply System" for
important information about priming an empty
water supp y system.
Your refrigerator's water supply system includes
several tubing lines, a water filter, a water
valve, and a water tank. To ensure that your
water dispenser works properly, this system
must be completely filled with water when your
refrigerator is first connected to the household
wa!ersupp!y !!ne: .........................................................
i!!!!!!Si
¸iliiiilllliiliiiilllliiliiiilllliiliiiilllliiliiiilllliiliiiilllliiliiiilllliiliiiilllliiliiiilllliiliiiilllliiliiiilllliiliiiilllliiliiiilllliiliiiilllliiliiiilllliiliiiilllliiliiiilllliiliiiilllliiliiiilllliiliiiilllliiliiiilllliiliii