Datexx EXACTIME DRC-608 Panduan Pengguna - Halaman 4

Jelajahi secara online atau unduh pdf Panduan Pengguna untuk Jam Datexx EXACTIME DRC-608. Datexx EXACTIME DRC-608 5 halaman. Autoupdate radio controlled digital projection clock with thermometer

Halaman Cetak

SETTING ALARMS

ALARM 1 setting
-In the ALARM 1 Display:
* Press and hold SET 1 for about 3 seconds: the alarm hour digits will
flash and then hour can be set by pressing UP [ ] or DOWN [ ] key.
* Press SET 1 again: the alarm minute digits will flash and then minute
can be set by pressing UP [ ] or DOWN [ ] key.
* Press SET 1 the third time, and the alarm minute digits "04" will flash
to set snooze time interval. Press UP [ ] or DOWN [ ] key. key to
set the required time period.
* Press SET 1 again, the Alarm1 time is set and [
* Repeat the same procedure to set an Alarm 2, using SET 2 button.
DISABLING ALARM
Press SET 1 or SET 2 buttons on the unit to disable any of the alarms.
When Alarm 1 and Alarm 2 are disabled, an applicable icon [
[
] will disappear from the unit's display.
2
Activating the Alarm
When the ALARM 1 or ALARM 2 is ringing, the relative alarm icon
[
] or [
] will be flashing.
2
1
* Press SET1 / SET2 key to turn the alarm off.
* Press top button 1 [LIGHT / SNOOZE] - alarm stops and the
backlight will turn on for 5 seconds with the repeat alarm indicator
( ) flashing.
Z
Z
* If the alarm is not turned off, it will stop in 4 minutes.
12
MOON PHASE INDICATOR
Displayed in accordance with the calendar
New
Waning
First
Waxing
Full
Waning
Moon
Crescent
Quarter
Gibbous
Moon
Gibbous
CARE OF YOUR ATOMIC PROJECTION CLOCK
WITH TEMPERATURE
This product is engineered to give you years of satisfactory service
if you handle it carefully. Here are a few precautions:
1. Do not immerse the unit in water.
2. Do not use any corrosive cleanser or chemical solution on the unit.
They may scratch the plastic parts and corrode the electronic circuit.
3. Do not subject the unit to excessive force, shock, dust,
temperature or humidity, which may result in malfunction,
shorter electronic life span, damaged batteries and distorted parts.
4. Do not tamper with the unit's internal components. Doing
so will invalidate the warranty on the unit and may cause
unnecessary damage. The unit contains no user-serviceable parts.
14
Time Zone setting
* Press and hold UP [ ] key for 3 seconds, to select the
corresponding time zone.
* Keep holding the UP [ ] button to switch to the time zone in
the following sequence:
Pacific time
Release the UP [ ] button to confirm the selected Time Zone
EL Backlight ON / OFF (PCR11ELW)
] icon will be displayed.
1
* Press top button 1
backlight
will come on and turns off after 5 seconds.
Projection Light and Adjustment
*Press button 1
] or
1
on and turn off after 5 seconds.
*After adapter is connected and "CONTINUE - PROJECTION"
switch is slid, the projection light will be enabled for continuous
projection.
5. Only use fresh batteries as specified in the user's manual.
Do not mix new and old batteries as the old ones may leak.
Always replace both batteries at the same time.
6. Always read the user's manual thoroughly before operating the unit.
7. Replace the batteries promptly when necessary (display becomes
dim) or store the batteries when not in use.
8. A soft cloth or paper towel may be used to clean your unit.
9. Keep the unit clean and dry to avoid any problems.
Last
Waning
Quarter
Crescent

SPECIFICATIONS

Temperature Measurement
Indoor Temperature
operating range
Temperature display unit
Temperature update interval
Indoor Temperature
Calendar and Clock
12/24 hour display in hh : mm format
Date Format: Month – Day format
Day of week: User- selectable in 3 languages
(English, French, Spanish)
Dual 4-minute crescendo alarm with snooze
Mountain time
Central time
Eastern time.
[LIGHT / SNOOZE] key-light and EL
[LIGHT /
SNOOZE]- projection light will come
13
: +23˚F to +122˚F with
0.2˚F resolution
-5˚C to 50˚C with
0.1˚C resolution
: ˚C or ˚F
: every 15 seconds
15