AUSTRALIAN MONITOR ACM604 Brosur - Halaman 2
Jelajahi secara online atau unduh pdf Brosur untuk Penguat AUSTRALIAN MONITOR ACM604. AUSTRALIAN MONITOR ACM604 2 halaman. Mixer amplifier
Juga untuk AUSTRALIAN MONITOR ACM604: Informasi Layanan (10 halaman)
Halaman CetakEngineered and Distributed By AUDIO TELEX COMMUNICATIONS PTY LTD (
NSW Tel: (02) 9647 1411 Fax: (02) 9648 3698 VIC Tel: (03) 9890 7477 Fax: (03) 9890 7977 QLD Tel: (07) 3852 1312 Fax: (07) 3252 1237 WA Tel: (08) 9228 4222 Fax: (08) 9228 4233
TAS Tel: (03) 6228 6373 Fax: (03) 6278 1063 SA Tel: (08) 8352 4444 Fax: (08) 8352 4488 Export Enquiries: [email protected]
Power Output
Maximum Load Per Amplifier
Power Bandwidth
Frequency Response
Total Harmonic Distortion
Signal To Noise Ratio
Tone Controls
Bass @ 100Hz: Boost +12dB Cut -12dB; Treble @ 10kHz: Boost +9dB Cut -9dB
Inputs
Input Sensitivity
Outputs
VCA Master Level Control
Phantom Power
Selectable per input of each amplifier module via an internal dip switch. 18 V
Controls
Indicators
Power Source
Power Consumption
Protection
Dimensions/Weight
Rack Mounting
Tone Generators
Muting
Built-in VOX muting. Channel 1 will mute channels 2 and 3 per amplifier
ARCHITECTURAL AND ENGINEERING SPECIFICATIONS
The four channel mixer amplifier shall have three universal input channels, accessible via a rear panel
barrier strip on each of the four amplifier modules. Each amplifier module shall allow remote VCA con-
trol of the master output. Phantom power selection on a per channel, per amplifier basis shall also be
included. A Vox triggered output shall also be available on an optional four tone generator card.
Each amplifier master section shall include one master VCA accessible gain control, two EQ controls,
one with 12dB of cut and boost at 100Hz and the other with 9dB of cut and boost at 10kHz. Speaker
outputs shall be transformer isolated at 100 volt, 70 volt & 8 ohms. The amplifiers must be capable of
delivering 60 watts RMS into a 160 ohm inductive load, with less than 0.5% distortion measured at
1 kHz and with system hum and noise of -74dB or better.
The amplifier shall be an Australian Monitor Installation Series model ACM604.
), 149 Beaconsfield Street, Silverwater, Sydney, NSW, 2128 Australia
ABN 78 001 345 482
-74dB with all controls at their centre position
Three mic/aux universal inputs per mixer amplifier module.
Mic/Line selection can be made via an internal dip switch
Mics: 1mV @ 200 Ohms; Aux 75mV @ 47K Ohms
Via a 1K pot added to the rear barrier strip of each amplfier module
3 Input channel gain controls, 1 Bass control, 1 Treble control,
1 Master VCA gain control per amplifier
AC 240V - 60Hz, 110V - 50Hz (special) 3 pin IEC connector
Overload and overdrive protection, plus AC and DC fuses
88mm H x 480mm W x 350mm D (Chassis Dimensions only). 17kg
Optional four tone generator module. Includes Bell, Pre-Announce,
Alert and Evac Tones, plus a vox triggered relay output.
Website: www.australianmonitor.com.au
4 x 60 Watts RMS
160 Ohms @ 100 Volts
60Hz - 15kHz < 0.5% THD
60Hz - 15kHz (± 3dB)
0.5% @ 1kHz rated power
Speaker: 100, 70 Volts, 8 Ohms
Power "on" LED
400 Watts
Standard