Gadgetree MINI DRONE Petunjuk Pengoperasian
Jelajahi secara online atau unduh pdf Petunjuk Pengoperasian untuk Drone Gadgetree MINI DRONE. Gadgetree MINI DRONE 3 halaman.
Halaman CetakMINI DRONE
Operating Instructions
Thank you for purchasing the Gadgetree Mini Drone.
INCLUDED
Mini drone
•
Transmitter remote control (requires 4 AA batteries, not included)
•
USB charging cable
•
Instruction manual
•
4 extra blades
•
Blade protective frame
•
Replacement thumb sticks
•
1 hand line
•
3 landing skids
•
BATTERY INSTALLATION
1. Use a screwdriver to remove the
screw on the side of the transmitter
then open the battery cover.
2. Install 4 AA batteries (not included)
and replace the battery cover.
We recommend InfiniCell batteries
for maximum perfromance.
3. Re-install the screw.
CHARGING
1. Connect the charging cable in the transmitter to the Mini Drone or
charge by connecting the included USB charging cable to a PC or AC
USB adapter. The green LED on the transmitter or the red LED on the
USB charging cable will turn ON and will turn OFF when changing is
complete. It will take approximately 30-60 minutes to completely charge
the Mini Drone.
CAUTIONS WHILE CHARGING
• Charge only in a dry, well ventilated area away from heat or explosive
products
• DO NOT charge the battery if the mini drone is still warm from flying.
Doing so may cause the battery to swell or catch on fire
• A battery when not in use for a long time will lose its charge automati-
cally. Charging or discharging for a long time may reduce the life of the
battery
INSTALLING LANDING SKIDS AND BLADE PROTECTIVE FRAME
1. Install landing skids to the bottom of the Mini Drone.
2. Install the blade protecting frame to the Mini Drone.
MODES
The transmitter has two built in modes. Mode 2
is the default mode, To switch to Mode 1, simply
press and hold the middle button on the throttle
then turn ON the transmitter.
FLYING YOUR MINI DRONE
1. Turn ON the Mini Drone.
2. Turn ON the transmitter. The LED will flash
quickly.
3. Once the LED stops flashing, push the throttle lever up
then back down quickly. You will hear a beep indicating that
the Mini Drone has entered into the pre-fly state.
NOTE: Ensure that the Mini Drone is on a level surface
when syncing to ensure a stable flight.
CAUTION
• If the LED on the transmitter is flashing slowly, syncing was unsuccess-
ful. Please turn OFF both the Mini Drone and transmitter then repeat
steps 1-3
• If the drone is pulling to one side or spinning while hovering, please
turn OFF both the Mini Drone and transmitter then repeat steps 1-3
• When the LED on the Mini Drone blinks slowly the battery is low
• Please charge the battery with the USB cable provided
MODE 1
Red light is on the left. Green light is on the right.
Battery cover
4 AA batteries
(not included)
Backward trimmer
Forward trimmer
Forward/Backward/
Left/Right/3D
Eversion
Left trimmer
OPERATING INSTRUCTIONS
Hover up and down
Push the throttle lever up or down
Turn left and right
Push the left lever left or right
FINE TUNING
Forward/backward
Use the backward/forward
trimmer to correct the Mini
Drone if it keeps flying
forwards or backwards
Power/Charge
r
LED indicato
One key automatic
return
Headless mode
Up/Down/Left/Right
sideways/High/Low
speed switch
Right sideways
fly trimmer
Right trimmer
Left sideways fly trimmer
Forward and backward
Push the direction lever up or down
Left and right sideways
Push the right lever left or right
Sideways
Use the left/right sideways
Use the right/left trimmer to
fly trimmer to correct the
correct the Mini Drone if it
Mini Drone if it keeps flying
keeps rotating
left or right
8065509
Turning