HI MART NHC-609 Manual - Halaman 2

Jelajahi secara online atau unduh pdf Manual untuk Perabotan Dalam Ruangan HI MART NHC-609. HI MART NHC-609 2 halaman. 4 bars & 2 shelves 1 pants (32mm)

Halaman Cetak
Caution for Assembling
The followings are presented to prevent from possible
danger or damage, occurring in setting up or using the
product. So obserbe the caution.
The pillar and horizontal bar are manufactured with steel pipe.
If you drop them, especially from another large ones, you may get
feet hurt or damage bottoms. So take care of an accident.
1.The pillar will be fixed on ceilings
and bottoms.
2.When a hanger takes a fall, it
possibly makes a baby get hurt
or breaks other article. So pre-
vent from the kind of troubles.
3.As a warning for a fall, lean the
pillar over the wall. Don't stand it
upright.
4.Check up safety(shaking, bolt
loose etc) for the time of using
the product.
Caution for Pillar Setting up
Don't set up the pillar on a weak part of ceilings or bottoms. A
hanger possibly has a tumble.
Distinguishment of Upper and Below Part, and Setting Method
Upper part is slim and below part is big from the fastening func-
tion device. Set up below pillar toward bottoms and upper pillar
toward ceilings
Check up before assembling
You have to remove fixation pin at below one touch button
before assembling pillars.
In case of broken fixation pin
one touch fixation device
►Push the button and
then pull pin the down.
►After remove the pin,
just rubbish
one touch button
pin
►Sharp as a pin or needle
to push it into the bo-
ttom, fall into the pillar.
Check up before disassembling
upper pillar
►Upper pillar down to below when
one touch
button
you press the one touch button
safety bolt
after release safety bolt behind one
touch fixation device
lower pillar
Part name and Quantity
Compare and check up composition and parts of the product
before assembling.
Upper fixation board (4 EA)
1
Upper and below Pillar (4 sets)
2
Hanger horizontal bar long (4 EA)
4
upper pillar
Open circle holder (8 EA)
5
(28mm)
Rubber O ring (8 EA)
6
one touch fixation device
Safety bolt (4 EA)
7
Use for One touch fixation device
Pants hanger bar (2 EA)
8
Pants hanger bar holder (2 EA)
9
lower pillar
Basket shelves holder (4 EA)
10
(32mm)
Basket shelves (2 EA)
11
Rubber O ring (6 EA)
12
Pants hanger (10 EA)
13
Lower fixation board (4 EA)
3
Safety bolt
►Safety bolt is at the back of the open circle
holder.
►Fix it with a hand slightly after position
regulation.
Parts have different colours depending on products.
Pillar Assembling
Assemble the product by inserting parts on the upper pillar
and the lower pillar in order of numbers.
Pillar 1
Pillar 2
Pillar 3
3
5
7
2
4
6
1
3
5
2
4
1
3
2
1
Open circle holder
Hanger horizontal
bar is inserted in
the open circle
holder.
Assemble is so
that holder home is
shown "U" shape.
Upper Pillar (28mm)
One touch
fixation device
Pull upper pillar longer
than 50cm and insert
the above parts in order
of numbers.
1
1
2
2
3
1
4
2
5
3
6
4
Lower Pillar (32mm)
3
7
5
Rubber ring places and fixes parts, so insert one rubber
ring under one part without fail.
The rubber ring inserted under parts is not shown.
Pillar 4
5
4
3
2
1
One touch
fixation device
1