Gage Bilt GB703SRVT Panduan Instalasi - Halaman 11
Jelajahi secara online atau unduh pdf Panduan Instalasi untuk Alat Listrik Gage Bilt GB703SRVT. Gage Bilt GB703SRVT 15 halaman.
Halaman Cetak
HANDLE
To inspect air cylinder bore, remove base cover (704125). Any further disassembly will require removal of the manifold-handle (744303) first.
For complete disassembly, start by removing base cover (704125). Next, holding tool upright, remove four screws (A-928). Lift manifold-handle
(744303) from handle assy (704132) and set aside o'ring (S832) and gasket (704129). Empty all hydraulic oil into an approved container and
dispose of in accordance with all environmental regulations applicable to your area. Place piston rod wrench (704149) down into top of power
cylinder (751131) and into the hex of piston rod assy (704138). While holding this wrench, remove flexlock nut (400559) using a 7/16" socket
wrench. Still holding piston rod wrench, remove air piston assy (704121) using packing plug wrench (704150), by turning counterclockwise.
When air piston assy (704121) is completely free from piston rod assy (704138), tap or push on the piston rod wrench to eject air piston assy
(704121) from bottom of handle assy (704132). After removal of air piston assy (704121), slide piston rod assy (704138) back up to the end of its
travel. Using packing plug wrench (704150) remove packing plug (704118). With packing plug (704118) removed, power cylinder (751131) can
be removed by pushing on power cylinder tool (704151) when inserted into top of power cylinder (751131).
To reassemble the handle assy (704132), reverse the above procedure, being certain that all o'rings are properly lubricated before installation.
Torque packing plug (704118) to 45 foot lbs. Attach the seal guide (704152) to the piston rod assy (704138) and tap the piston rod assy (704138)
through the packing plug (704118). Attach air piston assy (704121) and flexlock nut (400559). Torque flexlock nut to 40 inch lbs. Attach air pis-
ton assy (704121) to piston rod assy (704138). With the piston rod in the down position, fill oil passage on top of handle assy (704132) with
automatic transmission oil, Dexron III or equivalent, when looking at top of handle assy (704132) the oil passage is the hole that has a counter-
bore for (S832) o'ring. Replace gasket (704129) and o'ring (S832), just prior to replacing manifold-handle (744303). (See Filling & Bleeding in-
structions.)
AIR VALVE
:
WARNING
Disconnect tool from its air source before disassembly.
To disassemble, first disconnect tool from its air source. Remove pin (704244) and muffler (704146). Insert valve extractor (S1178)
into end of valve plug (704145) and pull it out. Using the same procedure, pull out valve spool assy (703142). NOTE: It should never
be necessary to remove valve sleeve (703139) unless the ports in the valve sleeve (703139) are plugged from contaminated air. If
ports are plugged, use needle nose pliers to grasp end of spring (704141), turning clockwise and pulling to dislodge from groove in
casting. NOTE: valve spring tool (704162) will facilitate the proper installation of the spring (704141), valve sleeve (703139) can be
pulled out using valve sleeve removal tool (704163).
S832 - O'RING
704129 - GASKET
704313 - PLUG
704132 - HANDLE ASSY
S734 - RETAINING RING
751131 - POWER CYLINDER
401102 - BACK-UP RING
PISTON ROD ASSY
(INCLUDES 401102 & S945)
403805 - O'RING
S945 - O'RING
704138
A-928 - BUTTON
HEAD CAP SCREW (4)
A-249 - SWIVEL
400781 - O'RING
703139 - VALVE SLEEVE
704141 - SPRING
400778 - O'RING
703142 - VALVE SPOOL
ASSY
400783 - O'RING
704145 - VALVE PLUG
400783 - O'RING
704146 - MUFFLER
704244 - PIN
11
A-287 - O'RING
S115 - BACK-UP RING
405757 - O'RING
704118 - PACKING PLUG
S115 - BACK-UP RING
A-287 - O'RING
S731 - BACK-UP RING
S730 - QUAD RING
S731 - BACK-UP RING
704121 - AIR PISTON
ASSY
400559 - FLEXLOCK NUT
S725 - O'RING
704125 - BASE COVER
9/14