Hi-Force HFG Series Buku Petunjuk

Jelajahi secara online atau unduh pdf Buku Petunjuk untuk Sistem Pengangkatan Hi-Force HFG Series. Hi-Force HFG Series 4 halaman. Hydraulic cylinders

Halaman Cetak

Model Series: HVL, HPS, HLS, HSS, HAS, HHA, HHS, HHR, HDA, HFL, HFG, HSG, HGG, HPC.

NOTE: Spare parts sheets for these products are

available from the Hi-Force website at:

www.hi-force.com

or from your local regional Hi-Force Sales office or

authorized local Hi-Force distributor.

1.0 Inspection of the product upon receipt:

On receipt of the product, visually inspect the item

for any evidence of shipping damage. Please note

shipping damage is not covered by warranty. If

shipping damage is found notify the carrier

immediately and refrain from putting the product

into service. The carrier is responsible for repair

and replacement costs resulting from damage in

transit shipment.

2.0 Safety Precautions:

Read and follow all the instructions and safety

warnings carefully prior to use of the equipment.

Failure to do so could result in equipment damage

or failure of the equipment or personal injury. Hi-

Force will not be held responsible for any damage

to the equipment or personal injury resulting from

unsafe use of the product, lack of maintenance or

incorrect operation. If in doubt on the correct usage

of any Hi-Force equipment, contact your nearest Hi-

Force office or distributor. If the operator has not

been trained on high pressure hydraulic equipment

and its safe use consult your local Hi-Force sales

office who can offer you training courses for

operators.

All operators should ensure that all necessary

personal protective equipment as specified by their

employer is worn when operating any hydraulic

equipment. Safety shoes, safety glasses/ visor and

Hi-Force Limited – Prospect Way – Daventry – Northants NN11 8PL – United Kingdom

Tel: +44(0) 1327 301000: Fax: +44(0) 1327 706555: Website: www.hi-force.com

INSTRUCTION MANUAL – HYDRAULIC CYLINDERS:

protective gloves should be worn at all times. All

relevant risk assessments should be completed

prior to use of the equipment.

Warning: Do not work under a load supported

only by hydraulic means. A cylinder, when used as a

lifting device should not be used as a load holding

device. All loads once lifted, should be supported by

rigid mechanical means. If load holding is required

by the application where external mechanical

means cannot be used, HFG/HFL Failsafe cylinders

should be considered. To avoid personal injury keep

hands and feet clear of the cylinder and workpiece

during operation.

Do not exceed the rated capacity of the

hydraulic cylinder and never attempt to lift a load

greater than the stated capacity of the cylinder. Hi-

Force hydraulic cylinders are designed for a

maximum working pressure of 700 BAR (10,000

PSI). Do not connect a pump with a higher rated

pressure capacity to any Hi-Force cylinder of this

model series.

Keep hydraulic equipment away from flames

and direct heat.

Hydraulic equipment must only be serviced by a

qualified technician.

To protect your warranty, only use Hi-Force's

hydraulic oil.

Immediately replace any worn or damaged parts

using genuine Hi-Force parts only.

Do not adjust the external pressure relief valve on

any Hi-Force cylinder.

The system operating pressure must not exceed the

pressure rating of the lowest component in the

system. Where possible, use a pressure gauge to

monitor the system.

Avoid damaging hydraulic hose. Always route hoses

to ensure that they are free from sharp bends and

kinks. Using a bent or kinked hose will cause severe

back-pressure and can also lead to the failure of the

hose.

Never lift or carry any hydraulic components

by the hose or hoses connected to them.

Do not handle a pressurized hydraulic hose.

Oil escaping under pressure from a ruptured

hose can penetrate the skin and lead to a serious

medical emergency and in certain cases death.

Should this incident happen medical attention must

be sought immediately.