Dynabrade 3A2827 Petunjuk Penting Pengoperasian, Pemeliharaan, dan Keselamatan - Halaman 4

Jelajahi secara online atau unduh pdf Petunjuk Penting Pengoperasian, Pemeliharaan, dan Keselamatan untuk Sander Dynabrade 3A2827. Dynabrade 3A2827 4 halaman. 3,200 rpm rolling pin sander

Halaman Cetak
Buy parts on line at https://Dynashop.co.uk/ for all things Dynabrade
Disassembly/Assembly Instructions (continued)
3. Line up hole in valve stem with hole in housing (looking past brass bushing). Insert 01472 Tip Valve so that the metal pin passes through the hole in the
valve stem. Install 01468 Spring (small end toward tip valve).
4. Assemble felt muffler into 94522 Muffler Cap. Install 94521 Muffler Base onto muffler cap.
5. Install 95438 O-Ring into groove on muffler base. Place 95375 O-Ring and 94526 Spacer into recessed area of muffler cap.
6. Slip 94523 Inlet Adapter through muffler assembly and install 95711 Retainer Ring into groove on inlet adapter.
7. Install 01564 Air Control Ring into valve body housing.
8. Apply Loctite
®
#567 PST Pipe Sealant to threads of 94523 Inlet Adapter and install entire muffler assembly onto valve body (torque 23.0 N•m/200 in. - lbs.).
9. Replace air fitting. Secure inlet adapter with a wrench before tightening air fitting.
Tool Assembly Complete. Please allow 30 minutes for adhesives to cure before operating tool.
Important: Motor should now be tested for proper operation at 90 PSIG. If motor does not operate properly or operates at a higher RPM than marked on the
tool, the tool should be serviced to correct the cause before use. Before operating, place 2-3 drops of Dynabrade Air Lube (P/N 95842) directly into air inlet
with throttle lever depressed. Operate tool for 30 seconds to determine if tool is operating properly and to allow lubricating oils to properly penetrate motor.
Loctite
®
is a registered trademark of Loctite Corp.
96174 Motor Tune-Up Kit
•
Includes assorted parts to help
maintain and repair motor.
®
Dynaswivel
•
Swivels 360° at two locations which allows an
air hose to drop straight to the floor, no matter
how the tool is held.
•
94300 1/4" NPT.
Dynabrade Air Lube
•
Formulated for pneumatic equipment.
•
Absorbs up to 10% of its weight in water.
•
Prevents rust and formation of sludge.
•
Keeps pneumatic tools operating longer
with greater power and less down time.
95842: 1pt. (473 m)
95843: 1gal. (3.8L)
Visit Our Web Site: www.dynabrade.com
DYNABRADE, INC., 8989 Sheridan Drive • Clarence, NY 14031-1490 • Phone: (716) 631-0100 • Fax: 716-631-2073 • International Fax: 716-631-2524
DYNABRADE EUROPE S.àr.l.,
© DYNABRADE, INC., 2003
Buy parts on line at https://Dynashop.co.uk/ for all things Dynabrade
Accessories
Zone Artisanale • L-5485 Wormeldange—Haut, Luxembourg • Telephone: 352 76 84 94 1 • Fax: 352 76 84 95 1
Grease
•
Multi-purpose grease for all types of bearings, cams, gears.
•
High film strength; excellent resistance to water, steam, etc.
•
Workable range 0˚ F to 300˚ F
95541: Push-Type Grease Gun (one-handed operation).
95542: 10 oz. (283.5 g) tube.
52296 Repair Collar
•
Specially designed collar for use in vise to prevent damage
to valve body of tool during disassembly/assembly.
Open End Wrenches
•
95262: 14 mm
•
95263: 17 mm
®
DYNABRADE
PRINTED IN USA