Dynabrade 50324 Panduan Memulai Cepat - Halaman 2

Jelajahi secara online atau unduh pdf Panduan Memulai Cepat untuk Sander Dynabrade 50324. Dynabrade 50324 4 halaman. 4 1/2"- 5" pistol grip disc sander

Halaman Cetak

Buy parts on line at https://Dynashop.co.uk/ for all things Dynabrade

Important Operating, Maintenance and Safety Instructions

Carefully read all instructions before operating or servicing any Dynabrade

Warning: Hand, wrist and arm injury may result from repetitive work motion and overexposure to vibration.

Important: All Dynabrade rotary vane air tools must be used with a Filter-Regulator-Lubricator to maintain all warranties.

Operating Instructions:

Warning: Eye, face, respiratory, sound and body protection must be worn while operating power tools. Failure to do so may result in serious injury or death.

Follow safety procedures posted in workplace.

1. With power source disconnected from tool, securely fasten abrasive/accessory on tool.

2. Install air fitting into inlet bushing of tool. Important: Secure inlet bushing of tool with a wrench before attempting to install the air fitting to avoid

damaging valve body housing.

3. Connect power source to tool. Be careful not to depress throttle lever in the process.

4. Check tool speed with tachometer. If tool is operating at a higher speed than the RPM marked on the tool or operating improperly, the tool should be

serviced to correct the cause before use.

5. Air tools are not intended for use in explosive atmospheres and are not insulated for contact with electrical power sources. Sanding/Grinding certain

materials can create explosive dust. It is the employers responsibility to notify the user of acceptable dust levels. Sanding/Grinding can cause sparks

which can cause fires or explosions. It is the users responsibility to make sure the work area is free of flammable materials.

Maintenance Instructions:

1. Check tool speed regularly with a tachometer. If tool is operating at a higher speed than the RPM marked on the tool, the tool should be serviced to

correct the cause before use.

2. Check the governor of this tool on a regular basis, the governor is preset at the factory to maintain the maximum rated speed for the tool,

if any inconsistency is found in the operating speed the tool must not be used and must be further tested by a Dynabrade factory technician.

3. Some silencers on air tools may clog with use. Clean and replace as required.

4. All Dynabrade rotary vane air motors should be lubricated. Dynabrade recommends one drop of air lube per minute for each 10 SCFM (example: if

the tool specifications state 40 SCFM, set the drip rate of your filter-lubricator at 4 drops per minute).

Dynabrade Air Lube (P/N 95842: 1 pt. 473 ml.) is recommended.

5. It is strongly recommended that all Dynabrade rotary vane air tools be used with a Filter-Regulator-Lubricator to minimize the possibility of misuse due

to unclean air, wet air or insufficient lubrication. Dynabrade recommends the following: 11405 Air Line Filter-Regulator-Lubricator — Provides accurate

air pressure regulation, two-stage filtration of water contaminants and micro-mist lubrication of pneumatic components.

Operates 40 SCFM @ 100 PSIG has 3/8" NPT female ports.

6. Use only genuine Dynabrade replacement parts. To reorder replacement parts, specify the Model #, Serial #, and RPM of your machine.

7. A Motor Tune-Up Kit (P/N 96047) is available which includes assorted parts to help maintain motor in peak operating condition.

8. Mineral spirits are recommended when cleaning the tool and parts. Do not clean tool or parts with any solvents or oils containing acids, esters,

keytones, chlorinated hydrocarbons or nitro carbons.

Safety Instructions:

Products offered by Dynabrade should not be converted or otherwise altered

from original design without expressed written consent from Dynabrade, Inc.

•

Important: User of tool is responsible for following accepted safety codes such as those published by the American National Standards Institute (ANSI).

•

Operate machine for one minute before application to workpiece to determine if machine is working properly and safely before work begins.

•

Always disconnect power supply before changing abrasive/accessory or making machine adjustments.

•

Inspect abrasives/accessories for damage or defects prior to installation on tools.

•

Please refer to Dynabrade's Warning/Safety Operating Instructions Tag (Reorder No. 95903) for more complete safety information.

•

Warning: Hand, wrist and arm injury may result from repetitive work, motion and overexposure to vibration.

All Dynabrade motors use the highest quality parts and metals available and are machined to exacting tolerances. The failure of quality pneumatic motors can most

often be traced to an unclean air supply or the lack of lubrication. Air pressure easily forces dirt or water contained in the air supply into motor bearings causing

early failure. It often scores the cylinder walls and the rotor blades resulting in limited efficiency and power. Our warranty obligation is contingent upon proper use

of our tools and cannot apply to equipment which has been subjected to misuse such as unclean air, wet air or a lack of lubrication during the use of this tool.

Following the reasonable assumption that any inherent defect which might prevail in a product will become apparent to the user within one year from the date

of purchase, all equipment of our manufacture is warranted against defects in workmanship and materials under normal use and service. We shall repair or

replace at our factory, any equipment or part thereof which shall, within one year after delivery to the original purchaser, indicate upon our examination to have

been defective. Our obligation is contingent upon proper use of Dynabrade tools in accordance with factory recommendations, instructions and safety

practices. It shall not apply to equipment which has been subject to misuse, negligence, accident or tampering in any way so as to affect its normal

performance. Normally wearable parts such as bearings, sanding pads, rotor blades, etc., are not covered under this warranty.

Model

Motor

Number

HP (W)

RPM

50320

.58 (433)

8,000

50321

.75 (559)

11,000

50324

.75 (559)

11,000

50325

.75 (559)

11,000

Additional Specifications: Hose I.D. Size 3/8" (10mm)

Buy parts on line at https://Dynashop.co.uk/ for all things Dynabrade

Notice

One Year Warranty

Air Inlet

Sound

Air Flow Rate

Thread

Level

CFM/SCFM (LPM)

1/4 NPT

72 dB(A)

4/30 (850)

1/4 NPT

72 dB(A)

4/32 (906)

1/4 NPT

72 dB(A)

4/32 (906)

1/4 NPT

72 dB(A)

4/32 (906)

(PD07•29)

Abrasive Power Tool.

Air Pressure

Spindle

PSIG (Bars)

Thread

90 (6.2)

5/8"-11 male

90 (6.2)

5/8"-11 male

90 (6.2)

3/8"-24 female

90 (6.2)

3/8"-24 female

Weight

Length

Height

Pound (kg)

Inch (mm)

2.2 (1.0)

6-5/8 (168)

5-5/8 (143)

2.2 (1.0)

6-5/8 (168)

5-5/8 (143)

2.2 (1.0)

6-5/8 (168)

5-5/8 (143)

2.2 (1.0)

6-5/8 (168)

5-5/8 (143)