Dynabrade 52451 Manual - Halaman 4

Jelajahi secara online atau unduh pdf Manual untuk Sander Dynabrade 52451. Dynabrade 52451 4 halaman. Vertical disc sander

Halaman Cetak

Disassembly/Assembly Instructions (continued)

13. Install 52477 Gasket and 52461 Housing Cap with 95720 screws and 01791 Washers, tighten screws to 9 N•m/80 in. - lbs.

14. Place complete motor assembly into housing. Be sure motor drops all the way into housing.

15. Motor adjustment must now be checked. With motor housing still mounted in vise, pull end of rotor and twist (10-15 lbs. force), rotor should turn freely

without drag. If drag or rub is felt, then increase preload or remove shim. Also, push end of rotor and twist (10-15 lbs. force), rotor should turn freely

without drag. If drag or rub is felt, then deload or add a shim.

16. Apply 2 drops of #271 Loctite® (or equivalent) to threads of adjustment bushing before tightening.

17. Slip 52491 Bushing through 52495 Nut and packing, and secure into housing.

18. Tighten 52491 Adjustment Bushing into housing torque 50 N•m/450 in. - lbs. Tighten valve body into housing.

19. Secure inlet bushing into vise. Place 52495 Nut and 01746 O-Ring onto valve body. Swivel 52494 Valve Body to desired throttle lever position.

20. Tighten 52495 Nut to 45 N•m/400 in. - lbs. Roll 07136 Grip back into place.

Tool assembly is complete. Please allow 30 minutes for adhesives to cure before operating tool.

Important: Motor should now be tested for proper operation at 90 PSI. If motor does not operate properly or operates at a higher RPM than marked on the

tool, the tool should be serviced to correct the cause before use. Before operating, place 2-3 drops of Dynabrade Air Lube (P/N 95842) directly into air inlet

with throttle lever depressed. Operate tool for thirty seconds to determine if tool is operating properly and to allow lubricating oils to properly penetrate motor.

Loctite® is a registered trademark of Loctite Corp.

Dynaswivel®

Swivels 360° at two locations which

allows an air hose to drop straight to

the floor, no matter how the tool is held.

•

95303 – 1/4" Hex Wrench

Visit our new Web Site via Industry.Net MROP On-Line: http://www.dynabrade.industry.net

DYNABRADE, INC., 8989 Sheridan Drive • Clarence, NY 14031-1490 • Phone: (716) 631-0100 • Fax: 716-631-2073 • International Fax: 716-631-2524

DYNABRADE EUROPE S.àr.l.,

Optional Accessories

95460 1/4" NPT

95461 3/8" NPT

95462 1/2" NPT

Zone Artisanale • L-5485 Wormeldange—Haut, Luxembourg • Telephone: 352 76 84 94 • Fax: 352 76 84 95

50283 – 7" Back-up Pad Assembly, 8,500 RPM max.

• Hard density.

• Includes 50287 Flange Nut.

• Accepts abrasive discs with 7/8" center hole.

• 96038 Spanner Wrench optional.

Wrenches

95304 – 24mm Open-End

96079 – 32mm Open-End

E-Mail: [email protected]

96259 Motor Tune-Up Kit:

•

Includes assorted parts to help maintain

motor in tip-top shape.

DYNABRADE

PRINTED IN USA