Hi-Velocity RPM-E 50 Panduan Instalasi - Halaman 2

Jelajahi secara online atau unduh pdf Panduan Instalasi untuk Unit Kontrol Hi-Velocity RPM-E 50. Hi-Velocity RPM-E 50 8 halaman. Refrigerant module

Halaman Cetak

Refrigerant Modules (RPM-E)

The RPM-E series cooling module can be used with the Hi-

Velocity Fancoil, installed in many different positions. It is pre-

piped with an adjustable, heat pump ready, thermal expansion

valve and comes with a bleed port, sight glass, suction and liquid

line access ports, freeze-stat, and two L brackets for mounting.

The RPM-E comes as a complete module and must be installed

in the vertical position on the return air side of the fancoil; the

unit cannot be turned on its side and is a draw through unit

only. The module offers multi-position airflow configurations for

horizontal, highboy, or counter-flow configurations. (Fig. RPM-

01)

The TXV (Thermal Expansion Valve), sight glass, access ports,

and freeze-stat* are already installed and are accessible through

an easy to remove access hatch. The liquid and suction lines have

male solder connections at a standard width making connections

to the condenser lines quick and easy.

*IMPORTANT: The freeze control serves the purpose

of preventing severe icing of the coil in the event of

an undercharge or low load on the coil. This piece of

equipment must be used at all times. Lack of use of

the freeze-stat will result in RPM-E related warranty

issues being voided.

Configurations

When installing, follow the recommendations shown in

Table 01, demonstrated in Fig. 01. For example, a horizontal

application could use A to B while highboy applications could

use A to B1. Do not use a combination of A to A1 or B to B1, as

this would bypass the cooling coil completely. A1 is not to be

used for outlet airflow. The knock-outs can be removed with a

screw driver and hammer. Use caution when opening the knock-

outs, ensuring you do not damage the coil surface.

Table RPM-01 - RPM-E Cooling Module Configurations

Right

A to B

A to B1

A1 to B

A1 to B1

B to A

B1 to A

Important: If side A1 is going to be used in your selected

configuration, the extended drain pan must be removed.

www.hi-velocity.com

Wrong

B1 to A1

B to A1

A to A1

B to B1

-2-

Refrigerant Module Installation

Fig. RPM-01 - RPM-E Cooling Module Configurations

Rough Opening Sizes

RPM-E 50

RPM-E-70

RPM-E-100

RPM-E Drain Pan Extension

The RPM-E Drain Pan Extension (DPE) is to be removed for up

flow (vertical) return air applications (avoid installing the RPM-E

in counter flow applications).

To remove the pre-installed DPE, first remove left side access

panel of the RPM-E Module. Remove the 3 - ¼ " screws that hold

the DPE in place, remove the DPE and replace ¼" screws into the

coil support (Fig. RPM-02). Replace the left side access panel.

Fig-RPM-02 - Remove DPE

The lower knockout can now be removed, using a screwdriver

and hammer (Fig-RPM-03). Use caution when removing knockouts

ensuring you do not damage the coil inside the module.

Fig-RPM-03 - Remove Knockout

Module RPM-E

A or B

A1 or B1

"L X 13

"L X 9"W

3/4

1/4

3/4

(298mm X 337mm)

(298mm X 229mm)

"L X 13

"L X 9"W

3/4

1/4

3/4

(425mm X 337mm)

(425mm X 229mm)

"L X 13

"L X 9"W

3/4

1/4

3/4

(578mm X 337mm)

(578mm X 229mm)