Daylight Ultimate U21098 Petunjuk Manual - Halaman 5

Jelajahi secara online atau unduh pdf Petunjuk Manual untuk Pencahayaan Rumah Daylight Ultimate U21098. Daylight Ultimate U21098 14 halaman. Floorstanding lamp

Halaman Cetak

ENGLISH

Thank you for purchasing this Daylight product. To register your

purchase and read more information about your guarantee,

please go to www.daylightcompany.com

To ensure correct and safe operation please read the following

and retain for future reference.

GENERAL INFORMATION

The Ultimate Floorstanding Lamp provides light, magnification,

chart/pattern holding facility and a storage tray. The accessories

may be removed when not required converting the lamp into an

attractive sitting room lamp. It is supplied in self assembly form

– Please follow the instructions below for quick and easy

assembly.

SETTING UP YOUR LAMP

• Carefully unpack the lamp. You should have the following

parts:

Weighted Base

Base Pole

Main Assembly

An electrical cable fitted with a foot switch and plug

passes through

Lamp Shade

Shade Securing Ring

20w ES(E27) Energy Saving Bulb

Flexible Arm with 1.75X magnification lens.

Flexible Arm with chart/pattern holder clip.

Storage Tray with transparent lid.

• Assemble the lamp as follows:

- Screw the Base Pole

taking care not to cross the threads. Ensure that the pole is

tight.

- Screw the short pole

- Screw the Main Assembly (

Base Pole

. Ensure the assembly is screwed tight. Also

take care not to tangle the cable. If it does get tangled

make sure it is untangled before the lamp is used.

- Unscrew the Shade Securing Ring

at the end of the curved pole

into position. Replace and tighten the Shade Securing

Ring

- Screw in the 20w Energy Saving Bulb

BY THE PLASTIC BASE NOT THE GLASS PART. DO NOT

OVERTIGHTEN.

- If required, insert the flexible arms with lens

attachments into the holes on the Accessory Supports

either side Lower Mount

- If required, fit the Tray

The tray should be offered up to the pole at 45°, hooked

on to the pole, rotated to a horizontal position and locked

in place with the latch. It should be fitted to the Fixed Pole

at any height between the Lower Mount

Upper Mount

- Your lamp is now ready for use.

OPERATION

Plug the lamp into a convenient electrical socket and switch on

using the footswitch. The height may be adjusted by pressing in

the button

and moving the pole up or down as required.

with a detached short pole

and

on to the thread on the Base

on to the Main Assembly

) on to the

from the lampholder

and place the shade

GRIP THE BULB

and clip

to the pole as shown in

and the

REMOVING ACCESSORY SUPPORTS

To enhance the look of the lamp the Accessory Supports

used to hold the magnifier and clip may be removed. Pull the

flexible arms

off the supports then unscrew and remove them. Re-fit the End

Caps

to the Lower Mount

order.

CLEANING

CAUTION: BEFORE CLEANING UNPLUG THE LAMP FROM

THE ELECTRICAL SUPPLY.

• If the lamp requires cleaning simply dust it to keep it clean.

• If the shade becomes dirty remove the bulb and the shade.

Clean the shade with a soft cloth or in warm soapy water.

Thoroughly dry the shade before re-fitting.

• Take particular care when cleaning the high quality acrylic

lens. To avoid scratches use only a soft cloth dampened with

warm soapy water. NEVER USE AN ABRASIVE CLEANER.

Take care not to touch the lens with sharp objects.

• The tray may be cleaned with a soft cloth or in warm soapy

water. Thoroughly dry before re-fitting to the lamp.

• Do not use metal polish or spray cleaners on your lamp as

they will damage the surface.

REPLACING THE DAYLIGHT BULB

• Always switch off and remove the plug from the mains supply

and allow the lamp to cool before changing the bulb. NEVER

touch the bulb while the lamp is switched on.

• The lamp is supplied with a 20w watt (equivalent to a 100w

Tungsten Bulb), E27 screw fitting Low Heat Daylight

Simulation Bulb. (This type of bulb is more suitable for

detailed work rather than a hot tungsten bulb)

THE MAXIMUM WATTAGE BULB THE LAMP CAN ACCEPT IS

A 60W TUNGSTEN BULB - DO NOT USE BULBS OF A HIGHER

WATTAGE , THIS WILL DAMAGE YOUR LAMP AND INVALIDATE

YOUR GUARANTEE.

• Replacement Daylight Simulation Bulbs can be obtained

direct from your local stockist. Code No: D15200.

• Simply unscrew the old bulb and screw in the new bulb.

GRIP THE BULB BY THE PLASTIC BASE NOT THE GLASS

PART. DO NOT OVERTIGHTEN.

• The old bulb should be re-cycled where local facilities are

available.

SAFETY

WARNING: DO NOT LEAVE THE LENS UNATTENDED IN DIRECT

SUNLIGHT AS THIS CONSTITUTES A FIRE HAZARD. ALWAYS

REMOVE THE LENS FLEXIBLE ARM WHEN NOT IN USE.

CAUTION: Never touch the bulb when the lamp is switched on,

or position it so it may come into contact with curtains or drapes.

CAUTION: Take care not to raise the pole too high. The lower

Fig. 2

pole

should not come out of the Lower Mount

lamp may become unstable if this occurs.

CAUTION: The shade fitted to this lamp is specially designed to

suit its maximum wattage, changing the shade could affect your

lamp's electrical safety.

CAUTION: Take care not get the flexible cord tangled around the

weighted base or pole during assembly and during use.

CAUTION: If the external flexible cable of this luminaire becomes

damaged, it should be exclusively replaced by a suitably

qualified person in order to avoid hazard.

IN CASE OF DOUBT CONSULT A QUALIFIED ELECTRICIAN

out of the supports. Pull the End Caps

. Re-assemble in the reverse

as the