DynaColor 1080P15FPS Panduan Cepat

Jelajahi secara online atau unduh pdf Panduan Cepat untuk Kamera IP DynaColor 1080P15FPS. DynaColor 1080P15FPS 2 halaman. Full hd multiple streaming ip fixed dome camera

Halaman Cetak

The Quick Guide is for quick installing and connecting the Full HD Multiple Streaming IP Fixed Dome Camera. For

details, please refer to the IP Camera's User Manual.

Camera's Connectors

Connector

Pin No.

Reset Button

BNC

Alarm I/O

Audio I/O

DC 12V

Power

AC 24V

RJ-45

IP Camera Installation

Please follow the instructions below to complete IP Camera installation.

Power up the Camera

To power up the IP Camera, please plug the camera's DC 12V / AC 24V cable into the power terminal block.

Alternatively, connect the Ethernet cable to the camera's PoE port and plug the other end of the cable into a PoE

switch.

NOTE: If using PoE, make sure Power Sourcing Equipment (PSE) is in use in the network.

Ethernet Cable Connection

Connect one end of the CAT5 Ethernet cable to the RJ-45 connector of the IP Camera, and the other end of the cable

to the network switch or PC.

NOTE: In some cases, you may need to use an Ethernet crossover cable when connecting the IP Camera

directly to the PC.

Full HD Multiple Streaming IP Fixed Dome Camera Quick Guide

Definition

Remarks

Restore to factory default

Analog Video Output

GND (Input－)

Input＋

Alarm connection

Output－

Output＋

Output (L)

Output (R)

Two-way audio transmission

GND

Input

Power

Reserved

GND

Power connection

Power-1

Earth GND

Power-2

10/100 Mbps Ethernet/ PoE

NOTE: Check the status of the link indicator and activity indicator LEDs; if the LEDs are unlit, please check

LAN connection.

Green Link Light indicates good network connection.

Orange Activity Light flashes for network activity indication.

Before Login to the IP Camera

A client program will be automatically installed on your PC when connecting to the IP Camera. Before logging in to the

IP Camera, please ensure downloading the ActiveX control is allowed by either changing the ActiveX controls and

plug-ins or setting Internet's security level to default. For further details, please refer to the IP Camera's user manual.

ActiveX Controls and Plug-ins Settings

Step 1: Start the Internet Explorer (IE).

Step 2: Select <Tools> from the main menu of the

browser. Then Click <Internet Options>.

Step 3: Click the <Security> tab and select "Internet",

and click <Custom level> to change ActiveX

settings.

Step 4: Set "ActiveX controls and plug-ins" items to

<Prompt> or <Enable>.

IP Camera Login

The IP Camera's default IP address is: 192.168.0.250. Therefore, to access the IP Camera for the first time, set the

PC's IP address as: 192.168.0.XXX; for example:

IP Address: 192.168.0.100

Subnet Mask: 255.255.255.0

 Key in the IP Camera's IP address in the URL bar of the Web browser window and press "Enter."

 Enter the default user name (Admin) and password (1234) in the prompt request dialogue. Note that user name is

case sensitive.

Install the ActiveX Control

 After connecting to the IP Camera, the request for installing the ActiveX control will appear just below the URL bar.

 Right Click on the information bar, and press "Install ActiveX Control..." to permit ActiveX control installation.

 In the pop-up security warning window, click "Install" to start downloading DC Viewer software on the PC.

 Press "Finish" after DC Viewer installation is complete.

Internet Security Level

Step 1: Start the IE.

Step 2: Select <Tools> from the main menu of the

browser. Then Click <Internet Options>.

Step 3: Click the <Security> tab and select "Internet."

Step 4: Down the page, press "Default Level" and click

"OK" to confirm the setting. Close the browser

window, and open a new one later for

accessing the IP Camera