DynaColor W series Panduan Cepat
Jelajahi secara online atau unduh pdf Panduan Cepat untuk Kamera IP DynaColor W series. DynaColor W series 2 halaman. Full hd multiple streams micro dome ip camera
Juga untuk DynaColor W series: Panduan Cepat (2 halaman)
Halaman Cetak
The Quick Guide is for quick installing and connecting the Full HD Multiple Streams Micro Dome IP Camera.
For details, please refer to the IP Camera's User Manual.
Camera's Connectors (for Indoor Only)
No.
Connector
Pin
1
RJ-45
-
10/100 Mbps Ethernet / PoE
1
AC 24V: Power-1
2
Power
AC 24V / DC 12V
2
AC 24V: GND
3
AC 24V: Power-2
3
microSD Card Slot
-
For video recording storage
4
Video (BNC Connector)*
-
For analog Video Output
1
Alarm In (–)
2
Alarm In (+)
3
Alarm Out (–)
4
Alarm Out (+)
5
Alarm & Audio I/O
5
Audio Out (L)
6
Audio Out (R)
7
GND
8
Audio In
6
Default Button
-
Press the button with one finger to default the system.
(*) Optional
NOTE: Please insert the SD card into the microSD Card Slot before power on the camera. If the camera is
already powered on, reboot the camera after the SD card is inserted.
IP Camera Installation
Please follow the instructions below to complete IP Camera installation.
Power up the Camera
To power up the IP Camera, please plug the camera's DC 12V / AC 24V cable into the power terminal block.
Alternatively, connect the Ethernet Cable to the camera's RJ-45 port and plug the other end of the Cable into a PoE
switch.
NOTE: If PoE is used, make sure Power Sourcing Equipment (PSE) is in use in the network.
Ethernet Cable Connection
Connect one end of the CAT5 Ethernet Cable to the RJ-45 connector of the IP Camera, and the other end of the cable
to the network switch or PC.
NOTE: In some cases, Ethernet Crossover Cable might be needed when connecting the IP Camera directly
to the PC.
Full HD Multiple Streams Micro Dome IP Camera Quick Guide
Definition
Remarks
DC 12V: Power
DC 12V: Reserved
Power connection
DC 12V: GND
Alarm connection
Line Out
Line In
NOTE: Check the status of the link indicator and activity indicator LEDs. If the LEDs are unlit, please check
LAN connection.
Green Link Light indicates good network connection.
Orange Activity Light flashes for network activity indication.
Function Cable Definition (for Outdoor only)
No.
Connector
Pin
Pink
Line In
1
Audio I/O
Green
Line Out
1
Alarm In (–)
Alarm
2
Alarm In (+)
2
(4-Pin Terminal Block)
3
Alarm Out (–)
4
Alarm Out (+)
White
AC 24_1
3
Power
AC 24V
Gray
AC 24_2
4
Power DC Jack
-
DC 12V
5
Video (BNC Connector)
-
For analog Video Output
6
RJ-45
-
10/100 Mbps Ethernet / PoE
-
Default Button
-
Please refer to Default Button in the table under
*If the function cable is used, make sure the color pins are connected correctly.
Before Login to the IP Camera
A client program will be automatically installed on the PC when connecting to the IP Camera. Before logging in to the
IP Camera, please ensure downloading the ActiveX control is allowed by either changing the ActiveX controls and
plug-ins or setting Internet's security level to default. For further details, please refer to the IP Camera's User Manual.
ActiveX Controls and Plug-ins Settings
Step 1: Start the Internet Explorer (IE).
Step 2: Select <Tools> from the main menu of the
browser. Then click on <Internet Options>.
Step 3: Click on the <Security> tab and select
"Internet", and click on <Custom level> to
change ActiveX settings.
Step 4: Set "ActiveX controls and plug-ins" items to
<Prompt> or <Enable>.
Definition
Remarks
Two-way audio transmission
Blue
Green
Yellow
Orange
Power connection
Power connection
Camera's
Connectors.
Internet Security Level
Step 1: Start the Internet Explorer (IE).
Step 2: Select <Tools> from the main menu of the
browser. Then click on <Internet Options>.
Step 3: Click on the <Security> tab and select
"Internet".
Step 4: Down the page, click "Default Level" and click
on <OK> to confirm the setting. Close the
browser window, and open a new one later for
accessing the IP Camera.