Days Strider bootie 3 Panduan Pengoperasian - Halaman 10

Jelajahi secara online atau unduh pdf Panduan Pengoperasian untuk Skuter Days Strider bootie 3. Days Strider bootie 3 20 halaman. Mobility scooter

Halaman Cetak

7. Lower the handlebars by releasing the handle bar lock

(see fig 6 page 8). with the handlebars positioned in

the straight ahead position, place the steering

locking pin (fig 18) through the front location hole.

The handle bars are now prevented from swinging

during transportation.

Warning:

You must never attempt to drive your

bootie

with the steering pin fitted. Failure to observe this

warning will put you in a dangerous situation.

8.You are now ready to separate the two halves of our

bootie

FIG 18

FIG 19

FIG 20

Carefully separate the two halves of your

bootie

pulling upwards on the release mechanism knob(fig 19)

and tilting backwards the rear chassis. Lift the front

chassis upwards,until the front chassis is completely

separated from the rear chassis(fig 20).

Your

bootie

is now dismantled into five basic parts (fig 21).

You can now load your

bootie

Into your car (see fig 14,

page 17)

Caution:

Protect clothing when lifting Scooter parts, some

components may have lubricating fluids on their surfaces.

Work out the best position to stow each part of your

machine, this will vary with different car designs. An old

blanket can be used to stop the various parts rubbing against

each other. It is good practice to stand batteries upright and

locate them so they do not move and touch the battery posts

on any metal framework. Your

bootie

will increase the load in

your car, please remember this and adjust your driving to suit

this condition.

Note:

In some small cars the seat my meed to be stowed on

the rear seat of the vehicle. Use the cars safety belt to secure

the seat in position.

Caution:

The body mouldings on your

bootie

have not been

designed for lifting your machine. Use the firm metal lifting

handles only.

Warning:

Take care when lifting heavy parts. If in doubt

always seek assistance when lifting parts into or out of your

vehicle.

When using access ramps to load your

bootie

into a car,

always keep your body clear of your scooter to prevent

entrapment. Never ride your scooter when loading it into a

vehicle, failure to observe this warning could put you into a

dangerous situation.

Always make certain your scooter and any ancillary parts are

correctly tied down in the carrying vehicle to prevent

movement during acceleration and braking. Most modern cars

have anchor points in the floor for this procedure.

Remember you have increased the load in your car, please take

account of this and modify your driving accordingly.

Warning: Always make certain that your scooter is stored in

the carrying vehicle with the 'Freewheel' system in the engaged

position (see page 10).

The Seat.

Rear Chassis Powered Unit.

The Battery pack

Steering Platform Chassis.

The Basket.

HOW TO RE-ASSEMBLE YOUR bootie.

Your

bootie

is very easy to re-assemble once you reach your

destination. To re-assemble, follow the preceding procedure

in reverse order, noting the following.

1. When re-assembling the front and rear sections of your

bootie

,make certain you are on firm, level ground. Place

the front and rear chassis units close together with the

round tube of the front steering section facing the 'U'

shaped channel of the rear motive unit (see fig 22)

2. Pivot the rear chassis unit backwards onto the anti-tipping

wheels .

Warning:

Do not pivot the rear chassis backwards onto the

plastic body cover, failure to observe this warning will

damage the paint finish.

3. Lift the front platform and locate it onto the 'Unshaped

channel of the rear powered unit .

4. Lock the two chassis sections together .Pull the locking

mechanism knob up during this operation with an audible

"click".

Warning:

Keep hands clear of any 'pinch' points during this

operation. Failure to observe this warning could put you

into a dangerous situation.

5. The front and rear chassis parts are now fully locked.

Pull backwards and forwards on the seat mounting post to

determine that the two chassis parts are correctly located

together, no movement in the two chassis parts should

be found.

Warning:

Fully engage the safety pin mechanism

correctly as failure to do so could result in an accident,

please take particular care.

6. Replace the battery pack onto the chassis making certain

they are correctly located onto the velcro fastener.

FIG 21

RE-ASSEMBLING YOUR bootie

7. Replace your seat by following the instructions on page 7

and 8 of this manual.

When you have re-assembled your

power key to the 'on' position. The battery level gauge will

move and the 'green' status light will illuminate. This will

indicate that you have re-connected the battery connectors

correctly.

Test the drive function of your machine. Does your

bootie

move forwards and backwards correctly? If

your Scooter does not drive, the freewheel lever may be in

the 'disengaged' position, see section 'Freewheeling your

bootie'

page 10 in this manual.

Important notice:

pavement use only,

FOR A SEAT IN A MOVING VEHICLE.

Now enjoy your bootie

FIG 22

bootie

, switch the

Your

bootie

has been designed for

IT IS NOT A DIRECT REPLACEMENT