80/20 Xtreme DIY Garden Box Panduan Memulai Cepat - Halaman 3

Jelajahi secara online atau unduh pdf Panduan Memulai Cepat untuk Peralatan Rumput dan Taman 80/20 Xtreme DIY Garden Box. 80/20 Xtreme DIY Garden Box 4 halaman.

Halaman Cetak
G
P a n
G r a
1 / 4 "
A
39.281"
B
P a n
e l A
1 / 4 "
G r a
y H
D P E
F
43.647"
A
1502 – 50.250"
B
1502 – 36.334"
C
1502 – 12.000"
D
1502 – 36.334"
E
1502 – 12.000"
F
1504 – 40.647"
G
1502 – 45.000"
H
1504 – 45.000"
J
1503 – 45.000"
e l B
D P E
y H
P a n
e l A
1 / 4 "
G r a
y H
J
P a n
G r a
1 / 4 "
C
1
x
1
x
1
x
1
x
Arm to Base
D P E
E
e l C
D P E
y H
H
48.000"
Panel D (not shown) twin wall
Polycarbonate installs into
the lid of the garden box.
4
x
Hardware
AA Single Tab End Fastener
BB 5/16-18 x .750" SHCS
CC 5/16-18 Economy T-nut
DD 1/4-20 x .625" FHSCS
EE 1/4-20 Drop-in T-nut
x8
FF 5/16-18 x .500" BHSCS
Hardware for Lid Arm Top
• ¼-20 x 1.00" SHCS
x1
• ¼-20 Economy T-nut
• ¼-20 Washer
x1
Hardware for Lid Arm Bottom
• 5/16-18 x 1.00" BHSCS
• 5/16-18 Drop-in T-nut
• 5/16-18 Washer
x2
2
x
Accessories
Door Handle
x1
Adjustable Hinge
x2
2
x
Panel Gasket
53ft
End Cap
x8
Tread Strip
2
x
Tools Needed
• 3/16 Hex Wrench
2
x
• 5/32 Hex Wrench
GARDEN BOX
ASSEMBLY INSTRUCTIONS
Tip: When assembling, all closed-faced sides
of profiles should be facing outward.
Assemble one side
of the garden box by
connecting profile
B (1) and profile
C (1) to opposite
ends of profile A (1)
using preassembled
hardware. Attach to
bottom T-slot of profile A. Repeat process with
profile A (1), profile D (1) and profile E (1).
Attach profile A of
both assemblies
together using
profile G (2) and
fastener AA (4).
x16
x2
x2
x8
To build lid, connect
profile A (2) with
profile J (1) using
x8
fastener AA (2).
Slide panel D (1)
into U-shape. Install
x1
handle to second
profile J (1) using
fastener BB (2) and CC (2). Cap off lid using
fastener AA (2) to connect profile J with handle.
x2
x2
To connect the lid
arm, take panel E
and install half into
inside T-slot of base
and half to outside
access hole on lid.
For more details,
see how-to video.
Finish by installing panel gasket and using
fastener FF (8) to install end caps (8). Lastly, put
tread strip in T-slots where lid and base meet.
Slide panel A (2)
into subassemblies
and cap each one
off with profile F
(2) using fastener
AA (4). Be sure to
face tab of fastener
away from panel.
Install panel B
(1) and panel C
(1) to assembly
and cap off using
profile H (2) and
fastener AA (4).
To install lid onto
base, use hinges
(2) and fastener
DD (8) and EE (8).
Attach half of hinge
on lid and half on
back T-slot of base.
Arm to Lid