GALA F360 Panduan Pengguna - Halaman 4

Jelajahi secara online atau unduh pdf Panduan Pengguna untuk Perahu GALA F360. GALA F360 10 halaman.

Halaman Cetak

BOAT ASSEMBLING

Inspect the condition of the package for and report to your

Step 1:

dealer if you find any damages.

Open the

- Remove all the packaging plastic and cardboard carefully. Do

boat

not use knife.

- Check the completeness of the boat and make sure that no

any parts are missing. You must report the missing part to your

dealer immediately.

Step 2:

- insert floorboard #1 to the front of the boat and position the

Insert flooring

inflatable keel placing the keel inflation valve in the middle of

the opening in floorboard,

- insert the rear (last number) floorboard and make sure it goes

under the upper transom stops,

- insert other floorboards, carefully centering them,

- put two last floorboards like A-frame. Press the upper angle

and push it down to make the floorboards flat,

- insert side beams and make sure that they are sitting straight

and tight

Step 3:

- Open the pump, connect the pump hose to the pump onto

Inflate the

inflation opening.

- Connect bayonet adapter of the pump hose to the valve

boat

- Inflate the tube rear compartments first up to pressure

slightly below nominal, and the bow compartment the last

up to the nominal pressure (0.2 bar/ 3 psi). In this case the

flexible baffles in the tube will move towards the rear

compartments and equalize the pressure in all compartments.

You may use the manometer to measure the pressure level to

ensure the best performance of the boat and make sure that

the pressure is about nominal level. Nominal tube pressure is

mentioned on Capacity Plate.

- Inflate the inflatable keel up to nominal pressure, same as in

inflatable tube.

Step 4:

Unpack the seats and install them. For that slide the side seat

railings into the seat slots on both sides. Always keep the

Install the

seats at a distance not less than 100mm (4 inches) from the

seats

seat rail ends.

- Assemble the oars: connect the oar blade to the oar tube and

Step 5:

make sure that the fixation pin is locking the blade properly.

Install the

- Insert oarlock stainless steel pin into the oar hole and secure

oars

it with the oarlock cup tight.

- to store the oar in boat running position insert the oar tube

into the oar holder and make sure that the oar is held there

tight.

Step 6:

Install the motor following your motor User's Manual

Install the

instructions.

motor

- 4 -

VALVES OPERATION

INFLATION-DEFLATION VALVE operation:

OVERPRESSURE VALVE operation:

DRAIN VALVE operation:

OVERINFLATING AND OVERHEATING OF YOUR BOAT MAY CAUSE THE

BOAT DAMAGE. AVOID OVERPUMPING THE BOAT, LEAVING THE BOAT

NOT COVERED, USING HIGH-PRESSURE INFLATORS. USE MANOMETER TO

CHECK THE PRESSURE IN THE TUBE REGULARLY.

WARNING

- 5 -

Inflation-deflation valve has PUSH-

PUSH operating system: pressing

the central pin the valve switches

between OPEN and CLOSED. To

inflate the tube put the pin to

CLOSED position (pin moves UP).

To deflate the tube put the pin to

OPEN position (pin moves DOWN).

After inflation every valve must be

closed with the valve plug tight to

ensure airtightness of the tube.

Overpressure valve protects the

boat against unexpected pressure

increase over the maximum working

limit. In case of any tube pressure

increase or overinflating the gasket

of the valve will open automatically,

release all excessive air and bring

the tube pressure to nominal. Make

sure that the valve cup is always

clean. Check the valve operation

during boat maintenance.

Drain valve includes:

a) Lifting OPEN-CLOSE lever: in

upper position the valve is OPEN

and water can get out of the cockpit,

lower

position

the

valve

CLOSED and water passage is

blocked

b) one-way drain valve with petal

prevent the water coming into the

cockpit.

Close your valve when driving, and

open your valve to drain the boat if

you discover any water collection in

the cockpit.