HIFEI Technology SwordfishX 200A-8S Petunjuk

Jelajahi secara online atau unduh pdf Petunjuk untuk Pengontrol HIFEI Technology SwordfishX 200A-8S. HIFEI Technology SwordfishX 200A-8S 2 halaman. Brushless esc

Halaman Cetak

BRUSHLESS ESC INSTRUCTIONS

Thanks for purchasing

SwordfishX

brushless speed controllers manufactured

by HIFEI Technology Co., Ltd.

SwordfishX

series ESC are specifically devel-

oped to supply stable and strong power for R/C model boats beyond your ex-

pected.

Safety

Please always keep in safe when use ESC

Strongly recommend to calibrate the throttle range of transmitter when you first

use controller or when using a new /different transmitter or receiver

Before begin the running, turn on the transmitter BEFORE powering on the re-

ceiver.

When finish the running, power off the receiver BEFORE turning off the

transmitter.

Please DO NOT run Swordfish ESC without water flow.

Swordfish ESC is water-resistant, and thus cannot be soaked in water, which may

cause ESC failure or be burned.

Never disconnect the battery pack while the brushless motor is running, as this

could cause damage to the speed controller and/or motor. And such damage would

not covered under manufacturer's WARRANTY.

It is suggest to add additional capacitor bank (such as HIFEI capacitor-bank 63V)

in the flowing two situations:

A: When run Swordfish X HV ESC with high KV motor with 10s or more lipos.

B: When run Swordfish X HV ESC at max current for a long time.

Swordfish ESC is preset with default parameters in factory, which can be assem-

bled for running directly. In order to get optimum power performance and well

compatible to work with brushless motor, it is suggested to program ESC parame-

ters before first run.

Features

·32-bit Microprocessor with up to 80Mhz frequency.

·Aluminum PCB process makes the heat dissipation efficient

·High Power Ultra-Low Internal Resistance 263-7 MOSFETS

·Telemetry Real Data By Wireless WIFI.

·ESC is with built-in data logging, Pro is without data logging.

·ESC is water-proof to prevent spill water , and aluminum water-cooler pipe is

pre-mounted.

·Full protection soft, include signal lose protection (in 100ms), temperature pro-

tection, motor block protection.

·ESC has Auto detect Lipo cells feature. Forward running mode is developed for

competitions.

·ESC is fully programmable by Hifei software on computer, or by Hifei Wifi

dongle

·ESC firmware is upgradeable by Hifei software on computer when a new version

firmware becomes available.

Specifications

ESC

Voltage

Current / Max

SwordfishX 200A-8S

2-8 Lipos

200/ 280

Install your ESC

Please solder good quality connectors to ESC's motor wires and power wires before

connect ESC to motor and battery. When connect power wires to battery, it is IM-

PORTANT to correctly connect positive to positive, and negative to negative. Swap

any two motor wires' connecting can change the rotation direction.

In order to prevent and reduce any signal disturbance generated by ESC hardware,

please install the ESC far away from receiver.

Step ①:Connect ESC to brushless motor;

Step ②:Connect receiver to the throttle channel of receiver;

Step ③:Connect receiver to ESC‟s receiver cable;

Step ④:Connect negative(-) cable of ESC to the negative of battery;

Step ⑤:Then connect positive (+) cable of ESC to the positive of battery.

Step ⑥: Switch on the ESC, after two beeps ♪ ♪ ,it is ready to run.

Calibrate throttle of TX

Note: In the following 3 situations, it is required to calibrate the throttle range of transmitter.

-When it is the first time to use a new speed controller.

-When change a new TX or RX, or a set of new radio system.

-When upgrade the ESC into a new version of firmware.

Board Transmitter

Connect ESC to motor, plug receiver lead of ESC to throttle channel of RX.

Push joystick of transmitter to max throttle position, power on TX.

Power on receiver, connect ESC to battery. Motor emits three beeps in

drop

tones.

In the following, motor will emit four long beeps in flat tones.

After any one beep of the four long beeps, pull joystick to

zero immediately.

Then motor emits two beeps in up tones.

Calibrating is completed, it's ready to go.

Note:SwordfishX ESC can not run in reverse. If throttle range were calibrated from reverse

to neutral, the calibrating range will be invalid.

Page 1

BEC

Size (mm)

Weight

Program the ESC

4A,6V

110X55X28

240g

SwordfishX ESC supports to be more easily programmed the parameters by Hifei programming

devices, such as 'Hifei Wifi dongle' and 'Hifei USB Adoptor'(connection to PC).

Connect Wifi Dongle to SwordfishX

Hardware Request

• Keep the length of USB cable no more than 500mm

• Compatible to any kind of smart mobile phone,PAD or PC with iOS/Android/Windows

Operation System

• Support all kind of browsers such as: Chrome, IE, Safia, Firefox, etc.

Connecting the WiFi Dongle

• Connecting the cable to ESC and WiFi dongle ( Figure 1)

• Power on the ESC ( the red LED of dongle will light a while and then black out) , waiting

more than 20 seconds till the green led on dongle start to blink.

• Option SwordfishX in the WLAN list of your smart terminal

• Open your browser and input the default IP address & password as following:

IP address 192.168.1.16:2015

Password

12345678

Please read Wifi Dongle user manuals for more information

www.hifei.com

• Entered into the Home Page