HIFEI Technology KIII Pro 100A-6S Petunjuk Manual
Jelajahi secara online atau unduh pdf Petunjuk Manual untuk Kontrol Jarak Jauh HIFEI Technology KIII Pro 100A-6S. HIFEI Technology KIII Pro 100A-6S 10 halaman.
Halaman CetakINSTRUCTIONS
Safety
The brushless ESC is used for R/C electric powered model
!
airplane and helicopters, which are not toys. ONLY adults
can run it correctly according to this instructions, young
children must run it with guardianship of adults.
Please keep the propeller away from your body and others
!
all the time when the battery is connected.
It is suggested that you remove the propeller when you are
!
working on the airplane with the battery connected.
It is suggested that you remover the pinion when you are
working on a helicopter with the battery connected.
!
Please observe all local laws regarding the flying of remote
control airplane.
!
Never fly over others or near crowds.
!
Before beginning flying, turn on the transmitter BEFORE
powering on the receiver.
!
When finish the running, power off the receiver BEFORE
turning off the transmitter.
Never disconnect the battery pack while the brushless motor
is running, as this could cause damage to the speed
controller and/or motor. And such damage would not
!
covered under manufacturer‟s WARRANTY.
Features of Kingkong III Pro ESC
• 32-bit Microprocessor with up to 80MHz frequency.
• 4-14S Lipo support
• Max continuous current 160A / 200A in full
throttle ( KIII Pro 160A HV / KIII Pro 200A HV )
• Active FreeWheeling optional
• Motor PWM frequency 8-32K Hz
• Throttle resolution up to 1uS
• Throttle signal refresh rate up to 1K Hz
• Integrated RPM sensor to simplify the wiring for
external Governor
• Optimized the Governor Algorithm to ensure the
head speed more stable
• Fully CNC aluminum housing to efficient the heat
dissipation
Kingkong III Pro USER MANUALS
KingKongIII Pro
• Built-In data Logger ( logging parameters: battery
voltage/current/throttle output/temperature/motor
RPM)
• Combine with WiFi dongle (sold separately) to pro-
gram setting the parameters of esc and telemetry the
real-time flight data by any kind of smart cell phone
• Max RPM 240000 with 2 pole motor ( Heli Mode:
Max electric RPM 160000 )
Kingkong III Pro Series ESC
ESC
Voltage Conti. Amp
160A-KIII
4-14S
Pro-HV
Lipo
200A-KIII
4-14S
Pro-HV
Lipo
100A-KIII
3-6S
Pro-6S Lite
Lipo
KIII
Pro
3-6S
100A-6S
Lipo
*
Surge current could be reached under the condition of ESC in contact
with 5mph airflow of 25 (77F) or cooler air at full throttle.
Install your ESC
Add battery connector
You must attach a quality battery connector of your choice to
the red (positive) and black (negative) of power wires. Well
solder the connectors to the wires and ENSURE THAT PO-
LARITY IS CORRECT (red wire to battery red wire, black
wire to battery black wire). Follow the instructions provided
with battery connector.
Connect ESC to motor
Suggested to solder quality and corresponding size golden bul-
let connectors for your motor to the motor wires coming from
ESC.
*Swapping any two motor wires connection can change rota-
tion direction.
Connect to receiver
Connect the receiver lead (consisted of brown, red and orange
small wires with a black plastic connector on the end ) to throt-
tle channel of receiver in right polarity, brown wire to negative,
red wire to positive, orange wire to signal.
Kingkong III Pro HV ESC are OPTO, so separate receiver
battery or UBEC to supply power for receiver is required.
!
www.hifei.com
Surge
Amp(5s)*
160amp
220amp
200amp
250amp
100amp
130amp
100amp
140amp
Page 1
BEC
Couple-
OPTO
Couple-
OPTO
Switching
Max 5A
Switching
Max
5A/6V